manualshive.com logo in svg

Fluke SMFT-1000, Руководство пользователя, Страница: 39 / 48

Поделиться
Скачать
Fluke SMFT-1000 Скачать руководство пользователя страница 39

Multifunction PV Analyzer

Test Setup

35

5. Push 

 to save the results to memory.

A confirmation message with ID number shows on the display and then returns to the test 

screen.

Troubleshoot:

 If the voltage is not within an acceptable range, use the continuous test to 

find the diode that fails. See 

Continuous Diode Test

.

Blocking Diode Test

Blocking diodes ensure that the electrical current only flows in one direction “OUT” of the 

series array to the inverter, external load, controller, or batteries to prevent the current 

generated by the other parallel connected PV panels in the same array flowing back through a 

weaker (shaded) network and also to prevent the fully charged batteries from discharging or 

draining back through the array at night.
Blocking diodes can fail in both open and short circuit states. This test is important for 

installations where blocking diodes are fitted.
To set:

1. Turn the rotary switch on the PV Analyzer to 

.

The display shows the default Bypass Diode test mode. 

2. Push 

 for the 

Blocking Diode

 test mode.

3. Connect the test leads from the PV Analyzer to the blocking diode. 

Tip: Push 

 to see a connection diagram.

a. Connect green test lead to positive anode.
b. Connect yellow test lead to negative cathode.

Note

Blocking diodes can be measured in operational systems. There is no need to 

disconnect the modules or switch off the voltage/power.

4. Use 

 to set the pass/fail limit for the blocking diode voltage measurement.

To set limit:

a. Use 

 and 

 to select the digit to edit.

b. Use 

 to change the value.

c. Push 

 (Back) to return to the blocking diode test screen.

Shop for Fluke products online at:

1.888.610.7664

www.

MyFlukeStore

.com

Содержание SMFT-1000

















































Отзывы:

Нет отзывов