manualshive.com logo in svg

Fluke SMFT-1000, Руководство пользователя, Страница: 40 / 48

Поделиться
Скачать
Fluke SMFT-1000 Скачать руководство пользователя страница 40

SMFT-1000

Users Manual

36

5. Push 

 to start the measurement.

When the measurement is complete, the display shows:

measured voltage of blocking diode

measured current of blocking diode

Passed:

 

 and a short beep noise indicate the test passed when the results are greater 

than the preset limits.

Failed:

 

 and multiple beeps indicate the test failed when the results are less than the 

preset limits.

Note

This test checks that the voltage drop of the diode is within the expected range (limit). 

If the voltage drop is too low the diode is shorted, if the voltage is “OL” then the diode 

is open.

6. Push 

 to save the results to memory.

A confirmation message with ID number shows on the display and then returns to the test 

screen.

Troubleshoot:

 If the voltage is not within an acceptable range, use the continuous test to 

find the diode that fails. See 

Continuous Diode Test

.

Continuous Diode Test

Use the continuous diode test to test each diode of a PV cell and find the diode that fails.
To set:

1. Turn the rotary switch on the PV Analyzer to 

.

The display shows the default Bypass Diode test mode. 

2. Push 

 for the 

Diode

 test mode.

3. Connect the test leads from the PV Analyzer to a diode inside the panel junction box or 

disconnected diode. 

Tip: Push 

 to see a connection diagram.

4. Connect green test lead to positive anode.
5. Connect yellow test lead to negative cathode.

W

 Caution

For this test the diodes must not be powered or operational.

Shop for Fluke products online at:

1.888.610.7664

www.

MyFlukeStore

.com

Содержание SMFT-1000

















































Отзывы:

Нет отзывов