Flowserve Logix 3200MD Plus Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 61

background image

Logix

®

Digital Positioners FCD LGENIM0110-0 05/16

flowserve.com

14

Warning!



Covers must be properly installed in order to maintain environmental ratings.

Special Conditions for Safe Use:



The equipment must be installed in such a manner as to minimize the risk of impact or friction with other metal surfaces.



To avoid possibility of static discharge clean only with a damp cloth.



For Intrinsically Safe installations the positioner must be connected to suitably rated intrinsically safe equipment, and must be
installed in accordance with applicable intrinsically safe installation standards.



Substitution of components may impair Intrinsic Safety.



Use appropriately rated cable insulation at higher temperatures.



Contact Flowserve for flame path information.



For Type nA and Type tb installation only air or inert gas may be connected to the air supply inlet.



Provisions shall be made externally to provide transient overvoltage protection to a level not to exceed 140% of the peak rated input
voltage.



Using the box provided on the nameplate, the User shall permanently mark the type of protection chosen for the specific installation.
Once the type of protection has been marked it shall not be changed

Conditions spéciales pour une utilisation en toute sécurité:



Le matériel doit être installé de sorte à réduire au minimum le risque de choc ou de frottement avec d'autres surfaces métalliques.



Pour éviter les risques de décharge d'électricité statique Nettoyez uniquement avec un chiffon humide.



Pour les installations en sécurité intrinsèque, le positionneur doit être connecté à un équipement sécurité intrinsèque convenablement qualifié,
et doit être installé conformément aux normes d'installation sécurité intrinsèque applicables.



La substitution de composants peut compromettre la sécurité intrinsèque.



Utiliser une isolation appropriée du câble à des températures plus élevées.

Contactez Flowserve pour les informations de trajet de flamme.

Assessed to the following ATEX standards: EN 60079-0 :2012, EN 60079-11 :2012, EN 60079-1:2007, EN 60079-31:2009, EN 60529: 1991/A1:2001
Assessed to the following IECEx standards: IEC 60079-0: 2011, IEC 60079-11: 2011, IEC 60529: 1999, IEC 60079-1: 2007-04, IEC 60079-31:2013
Assessed to the following US standards: FM Class 3600 :2011,Class 3610 :2010, FM Class 315:2006, FM Class 3616:2011, FM Class 3810: 2005, ANSI/ISA
60079-0:2013, ANSI/ISA 60079-11:2014, ANSI/NEMA 250:2003, ANSI/IEC 60529:2004, INSI/ISA 60079-1: 2009

«
...
12
13
14
15
16
...
»

Содержание Logix 3200MD Plus






























































Отзывы:

Нет отзывов

Похожие инструкции для Logix 3200MD Plus

Бренд: Baelz Automatic Страницы: 33

Бренд: Flowserve Страницы: 34

Бренд: jbc Страницы: 15

Бренд: ABB Страницы: 72

IP8000-0 Series

Бренд: SMC Networks Страницы: 2

Бренд: SMC Networks Страницы: 18

Бренд: SMC Networks Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды