Flowserve Argus EK 71 Скачать руководство пользователя страница 59

Страница: 59 / 68

Argus Ball Valve EK, FK and HK Operating Manual – BA1000 EN

12 Transportation

Page 57 of 67

Transportation

12.1

Safety Messages

In order to prevent personal injury and/or property damage, ensure that
transportation work is only carried out by qualified personnel with appropriate
personal protective equipment (PPE) and suitable work tools.
See Chapter 2 Safety Information.

Risk of injury due to falling of suspended loads!

Falling of suspended loads may cause severe injury or death.



Never stand under suspended loads.

Risk of injury due to improper transportation!

Improper transportation may lead to severe injury.



Secure the Argus Ball Valve against twisting and tipping over.



Correctly attach the Argus Ball Valve.

If an actuator is present, never lift the complete unit with the

lifting gear only attached to the actuator!



Use protective packaging materials to protect the Argus Ball Valve
from damage during transport (e.g., packaging cover).



Observe all load-handling regulations.

Risk of property damage due to improper transportation!

Improper transportation of the Argus Ball Valve may cause damage.



Follow the procedures specified in the section below closely.

Содержание Argus EK 71





































































Результаты поиска

Содержание Argus EK 71

Отзывы:

Бренды по названию

Популярные бренды

Flowserve Argus EK 71, Установка, наладка, обслуживание

Результаты поиска

Содержание Argus EK 71

Отзывы:

Бренды по названию

Популярные бренды