background image

1.5 Warranty

Flomotion Systems, Inc. warrants all Flomotion Systems pumps against any defects that are due to faulty material or 
workmanship for a period of two years from date of shipment.In the event that a defect is discovered during the warranty 
period, Flomotion Systems, Inc. agrees that, at its option, it will repair or replace the defective product.  Any product 
repaired or replaced under this warranty will be warranted only for the remainder of the original product warranty period.
This warranty does not apply to consumable components of a product such as, but not limited to, hose, tubing, rollers, and
fuses.

Contact Flomotion Systems, Inc. or your distributor to initiate warranty support.  Products may not be returned without 
authorization from Flomotion Systems, Inc.  All returns shall be freight prepaid.

Limitations

This warranty does not cover:

Damage caused by acts of God, natural disaster, labor unrest, acts of war (declared or undeclared), terrorism, 

civil strife, acts of any governmental jurisdiction or any other cause beyond the seller's control

Damage caused by misuse, neglect, accident or improper application or installation

Damage caused by any repair or attempted repair not authorized by Flomotion Systems, Inc.

Any product not used in accordance with the instructions furnished by Flomotion Systems, Inc.

Any product not paid in full in agreed upon terms.

Modifications performed on this product by person(s) not authorized by Flomotion Systems, Inc.

Freight charges to return merchandise to Flomotion Systems, Inc.

Freight charges on expedited or express shipment of warranted parts or product

Travel fees associated with on-site warranty repair

This warranty contains the sole express warranty made by Flomotion Systems, Inc. in connection with its products.  All 
implied warranties, including with limitation, the warranties of merchantability and fitness for a particular purpose, are 
expressly disclaimed.

Some states within the United States do not allow the disclaimer of implied warranties and if this is true in your state the 
above limitation may not apply to you.  This warranty gives you specific rights, and you may also have other rights that 
vary from state to state.

This warranty constitutes the final, complete, and exclusive statement of warranty terms and no person is authorized to 
make any other warranties or representations on behalf of Flomotion Systems, Inc.

pg. 4

Содержание V21























Отзывы: