Flo CoRe+ Скачать руководство пользователя

Страница: 7 / 52

Pedestal Specifications

The pedestal is designed to be installed using these components: the pedestal enclosure, a cascading kit (on
certain pedestal models), and a pedestal anchor. An optional cable management system is also available.

3.1.

Pedestal

The pedestal has an access door latch that can be secured using a padlock (not included).

3.1.1.

Specifications

The table below displays the pedestal specifications:

Product family

CoRe+ MAX

Model

ACPE000022

Ingress protection rating

3R enclosure type; suitable for outdoor use

Shipping weight

Approximately 25 lbs. not including packaging

Security standard
compliance

UL 50E / CSA C22.2 No. 94.2
Enclosures for Electric Equipment, Environmental
Considerations

Specification information sticker

Charging station back plate

Latch

Access door screws

Access door

Safety warning sticker

Ground terminal

Ground sticker

Содержание CoRe+





















































Результаты поиска

Содержание CoRe+

Отзывы:

Похожие инструкции для CoRe+

Бренды по названию

Популярные бренды

Flo CoRe+, Руководство по установке

Результаты поиска

Содержание CoRe+

Отзывы:

Похожие инструкции для CoRe+

Бренды по названию

Популярные бренды