Flo CoRe+ Скачать руководство пользователя | Manualshive

Страница: 35 / 52

background image

35

6.4.2.

Before Getting Started

Follow the steps below before getting started:

CAUTION

: Before getting started, cut off the current to prevent an electric shock.

1.

Make sure to remove the security screw used to hold the counterweight during transport when unpacking
the cable management system.

2.

Install a cable management system on a new station OR install a cable management system on an existing
station by following the steps below:

6.4.2.1.

Before Installing a Cable Management System on a New Side-

by-Side Charging Station Installation

1.

First, install the pedestal and charging station. Refer to the

Installing the Pedestal and

Charging Station

section (

section 5.

) for more information and the

CoRe+ MAX Installation

Guide

as

needed.
2.

Then, prepare the installation material for the side-by-side charging station mount brackets

and cable management systems and follow the instructions in the

Cable Management System

Installation

section below.

CAUTION

: Before getting started, cut off the current to prevent an electric shock.

«
...
33
34
35
36
37
...
»

Содержание CoRe+





















































Отзывы:

Нет отзывов

Похожие инструкции для CoRe+

Бренд: A-Tach Mounts Страницы: 2

Бренд: EarthX Страницы: 17

Бренд: EarthX Страницы: 23

Бренд: Fantasea Страницы: 18

Бренд: Fantasea Страницы: 15

Бренд: Gainsborough Страницы: 2

Бренд: iDataLink Страницы: 30

Бренд: Kathrein Страницы: 7

Бренд: Kathrein Страницы: 2

Бренд: M-S Cash Drawer Страницы: 2

Бренд: M-Audio Страницы: 61

Q.HOME+ ESS HYB G2

Бренд: Qcells Страницы: 2

Бренд: Valor Страницы: 72

Бренд: Zamel Страницы: 12

Бренд: Pitney Bowes Страницы: 22

Бренд: Calix Страницы: 5

Бренд: AirTest Страницы: 4

Бренд: Flymo Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды