Flexicon PD12IDH Скачать руководство пользователя страница 17

Страница: 17 / 19

INSTRUCTION HANDBOOK

PD12IHS / PD12IDH

PD12IHS_PD12IDH IH EN 74-115-181 v2.01

Version: 2.01

Page 17 of 19

8 Interface and change of voltage

8.1 PD12 interface

1

2

3

4

1 =

External 1:

PIN 1:

INPUT FOR START SIGNAL
+5 - 50 VDC, min. 100 msec. positive-edge-trigged.

PIN 2:

OUTPUT, +24 VDC, MAX. 500 MA.

PIN 3:

GROUND.

PIN 4:

STATUS OUTPUT, MAX. +24 VDC, 100 MA.
Pin 4 is grounded via an open collector during filling.

PIN 5:

STATUS OUTPUT, MAX. +24VDC, 100 mA Pin 5 is complementary to pin 4.

2 =

External 2:

PIN 1:

INPUT FOR DISABLING.
+5 - 50 VDC. if this pin is activated, the drive will be disabled (no dispensing).

PIN 2:

OUTPUT, +24 VDC, MAX. 500 MA.

PIN 3:

GROUND.

PIN 4:

STATUS OUTPUT, MAX. +24 VDC, 100 MA.
Pin 4 is grounded via an open collector during filling.

PIN 5:

STATUS OUTPUT, MAX. + 24 VDC, 100 MA.
Pin 5 is complementary to pin 4.

3 =

Net 1

This socket is reserved for (RS-485) network communication.

4 =

Net 2

This socket is reserved for (RS-485) network communication.

Содержание PD12IDH




















Результаты поиска

Содержание PD12IDH

Отзывы:

Похожие инструкции для PD12IDH

Бренды по названию

Популярные бренды

Flexicon PD12IDH, Инструкция по эксплуатации

Результаты поиска

Содержание PD12IDH

Отзывы:

Похожие инструкции для PD12IDH

Бренды по названию

Популярные бренды