background image

                                                     

2

Safety Measures

 

 

Safety Precautions

 

To ensure your safety, please read through the following precautions before using this product

 

1. Please read, study and understand the instructions and all warning labels before use.

 

(It  is  recommended  to  familiarize  yourself  with  the  normal  operation  and  use  of  the  instrum

ent  before  using  this  product. 

 

(Information  is  available  in  this  manual  and  from  your  local  retailer) 

 

2. Be sure to keep this manual and make sure all warning labels are clear and complete.

 

3. The product is recommended to be installed by more than two people.

 

4. Please consult your physician for advice before you start exercising.

 

5. Please ensure safety   when using it in the presence of children.

 

6. Please be cautious when using it in the presence of children. 

 

7.  Please  check  the  wire  rope  regularly  for  any  signs  of  wear  and  tear,  which  may  cause  ce

rtain  danger  to  you.

 

8.  Please  keep  your  hands,  limbs,  and  clothes  stretched  so  that  you  can  fully  and  safely  use 

this  instrument.

 

9.  Be  aware  of  any  signs  of  possible  mechanical  problems,  including  worn  parts,  loose  hard

ware  and  cracked  welds.  In  case  of  any  of  the  above  signs,  stop  using  this  instrument  i

mmediately  and  contact  our  after-sales  service  department. 

 

10.  You  can  complete  the  assembly  with  a  wrench  or  hexagon  wrench.

 

 

 

 

Содержание MLD-M6































Отзывы: