Option 1-13: Siren/Horn Mute Control From Remote
Used to enable the remote mute function
1) Open the Vehicle Door
2) Turn on Ignition ( within 5 seconds )
3) Press and Release Lock Button
4) Press and Release Unlock Button
5) Press and Release the Lock Button
6) You will see 2 Parking light flashes indicating Option 1-13 has been enabled.
Option Programming Using the FT-OP500-KIT
The OP500 can be used to change anything in the Option Tables. It is required to change settings in the
Special Option Group.
STEP 1:
Make sure system is unlocked/disarmed.
Connect the antenna cable to the 4 or 6 pin port on
the top of the OP500. Once connected, the OP500 will power up as long as CN1 on the control module is
connected properly.
STEP 2:
Use the left or right arrow keys on the OP500 to select option. Use the up or down arrow
buttons to select the option setting. “1” is the default setting, “2”, “3”, and “4” are the optional settings.
Special Option Group 1: Change the timed output of Auxiliary 1 and 2.
STEP 3:
Hold the “W” (Write) button for 3 seconds. This finalize option changes to the control module.
Wait until OP500 displays “Success” before disconnecting.
To reset the options, hold the “R” (Reset) button and “W” (Write) buttons for 3 seconds. Then hold the
“W” button for 3 seconds.
Option Programming Using Compatible Remotes
Using a remote is a timed process so review this section before beginning. Options cannot be
programmed with 1 button remotes.
IMPORTANT:
Special Option Groups cannot be programmed with
remotes – OP500 must be used.
STEP 1:
Select the option you wish to program. Use the correct remote table below:
How to Program Options With 2 Way Remotes with Separate Lock and Unlock Buttons
Wait for chirp
between each
tap
Scroll Through
Menu (Wait for
flash between
each tap)
Select Option 1
Select Option 2
Select Option 3
Select Option 4
Option
Menu 1
Lock +
Unlock for 3
seconds
Tap Key
Button
Wait for corresponding
parking light flash and/or
siren chirp before
selecting option
Tap Lock
Button
Tap Unlock
Button
Hold Trunk
Button for
3 seconds
Tap Star
Button
16
Option
Menu 2
Lock + Key
for 3 seconds
Tap Key
Button
Tap Lock
Button
Tap Unlock
Button
Hold Trunk
Button for
3 seconds
Tap Star
Button
How to Program Options With 1 Way 4 Button Remotes
Wait for chirp
between each
tap
Scroll Through
Menu (Wait for
flash between
each tap)
Select Option 1
Select Option 2
Select Option 3
Select Option 4
Option
Menu 1
Lock +
Unlock for 3
seconds
Hold Trunk
+ Key for 3
seconds
Tap Lock
Button
Tap Unlock
Button
Tap Trunk
Button
Tap Star
Button
Option
Menu 2
Lock + Key
for 3 seconds
Hold Trunk
+ Key for 3
seconds
Wait for corresponding parking
light flash and/or siren chirp
before selecting option
Tap Lock
Button
Tap Unlock
Button
Tap Trunk
Button
Tap Star
Button
STEP 2:
Scroll through menu waiting for 1 parking light flash and/or siren chirp per line.
STEP 3:
Once finished scrolling through menu, wait for the parking lights and/or siren chirp to confirm
the option number. i.e. option 2-04 will flash and/or chirp 4 times. Select your option using the Lock,
Unlock, Trunk, or Start buttons.
Resetting to Factory Defaults:
To reset the options in a particular menu, enter the menu using your
remote. To reset options with a 2 Way remote tap the Trunk button 3 three times. To reset options with a
1 Way remote tap the Trunk button 3 times. Wait for parking lights to flash and/or siren chirp between
each tap. After the third tap, the menu will reset back to default. This must be done for each option menu
that must be reset
Troubleshooting
Alarm LED Diagnostics
When the alarm is triggered, the LED (if installed) will flash a certain amount of times as shown in the
table below.
Priority
Trigger
LED Flash Diagnostic
1
Door/Hood/Trunk/Ign
Triggered
2 flashes, pause, then repeat
2
2
nd
Shock Triggered
3 flashes, pause, then repeat
3
2
nd
Auxiliary Input
Triggered
4 flashes, pause, then repeat
4
Panic with remote
5 flashes, pause, then repeat
17
