manualshive.com logo in svg

Fireplace 42 Apex, Руководство по установке

Поделиться
Скачать
Fireplace 42 Apex Скачать руководство пользователя страница 8

8 

Finalizing the Installation 

 (for qualified installers only)

 

© Travis Industries 

4161018 

100-01436 

Fireplace Placement Requirements 

Clearances to Fireplace 

 

Sidewalls to the front of the fireplace must be 45” (1143mm) from the centerline of the fireplace (see 
“a” in the illustration below). 

 

Any combustible (bookshelf, column, etc.) that protrudes less than 7” (178mmmm) from the front of 
the fireplace must be placed a minimum 24-3/8” (620mmmm) from the centerline of the fireplace.  If 
this combustible protrudes farther, it must meet the sidewall clearance (see “b” and “c” in the 
illustration below). 

a

b

c

d

 

 

The fireplace requires a ½” (13mm) clearance to the back and sides (stand-offs are pre-installed to 
provide this clearance).  Do not place insulation or other material into this area.  Drywall or other 
combustibles must maintain a ½” clearance to the sides of the fireplace (see “d” in the illustration 
above). 

 

Fireplace should be located such that no doors, drapes, furniture or other combustibles can be 
placed close or swing closer than the minimum 48" clearance.  Due to the high heat output of this 
fireplace, choose a location away from high traffic areas. 

Содержание 42 Apex





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды