manualshive.com logo in svg

Fireplace 42 Apex, Руководство по установке

Поделиться
Скачать
Fireplace 42 Apex Скачать руководство пользователя страница 13

 Finalizing 

the 

Installation

  

(for qualified installers only)

 

13 

© Travis Industries 

4161018 

100-01436 

Air Cooled Chimney Requirements (8” Inner Dia., 12” Outer Dia.) 

Part Numbers (available through Travis Industries) 

Chimney Components 

Part # 

Anchor Plate – Air Cooled Chimney - 

REQUIRED

 

98900016 

Cooling Duct Kit -6” Diameter - 

REQUIRED

  

98900108 

48” Chimney Section 

98900001 

36" Chimney Section 

98900002 

24" Chimney Section 

98900003 

18" Chimney Section 

98900004 

12" Chimney Section 

98900005 

30° Offsets / Elbows (Qty 2) 

98900006 

Firestop (90°) 

98900007 

Firestop (30° - for angled sections) 

98900008 

Storm Collar 

98900009 

Round Termination Cap 

98900010 

Flashing 0-6/12 (for flat roofs up to 6/12 pitch - 26.5°) 

98900011 

Flashing 7-12/12 (for roofs 6/12 pitch to 12/12 – 26.5° to 45°) 

98900012 

Attic Insulation Shield 

98900015 

Anchor Plate Installation 

 

The air-cooled chimney requires an anchor plate that includes a cooling duct inlet.  Attach the anchor 
plate to the top of the fireplace with the four  included sheet-metal screws (see illustration below).  
The cooling duct inlet can be directed to any direction (typically it is directed to the right rear).   

 

Seal the fireplace connection with high-temperature silicone. 

 

Seal the flue liner with furnace cement. 

High-Temperature 

Silicone

Use high-temperature silicone to 

seal the anchor plate.

Furnace Cement

 

Содержание 42 Apex





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды