manualshive.com logo in svg

Fireplace 42 Apex, Руководство по установке

Поделиться
Скачать
Fireplace 42 Apex Скачать руководство пользователя страница 33

 Finalizing 

the 

Installation

  

(for qualified installers only)

 

33 

© Travis Industries 

4161018 

100-01436 

Hearth Requirements 

 

Local building codes may require a minimum hearth requirement different of what this manual states 

 

Hearth must extend 20" in front of the faceplate when it is not elevated (see local building codes).  
Hearths raised at least 6" must extend a minimum 18". 

 

Hearth must extend a minimum 8" to both sides of the door opening (44” wide) 

 

Hearth must be a minimum 1" thick of Durock Next Generation Cement Board (or equivalent material) 
with an R-value of 1.00. Multiple cement boards may be stacked to meet the required R-value of 
1.00. For example, two half-inch boards each with an R-value of 0.5 can be stacked together to meet 
the 1.00 requirement. 

 

Hearth must not rise more than 6-3/8" above the base of the fireplace 

Face

Fireplace

7-3/4”

6-3/8”

1-1/8”

ELEVATED HEARTH

20" Min. 

(Check Local Building Codes)

Minimum 1" 

cement board

(or equivalent)

Ember Strip

Tile or 
marble

Fireplace

Combustible 

Floor

FLOOR HEARTH

Elevated hearths must be 
constructed of non-combustible 
materials such as cement blocks 
(6” Min. / 6-3/8” Max.).

Minimum 1" 

cement board

(or equivalent)

Ember Strip

Fireplace

Combustible 

Floor

18" Min. 

(Check Local Building Codes)

Tile or marble

No combustible 

material permitted 

above this point

 

 

Содержание 42 Apex





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды