manualshive.com logo in svg

Fireplace 42 Apex, Руководство по установке

Поделиться
Скачать
Fireplace 42 Apex Скачать руководство пользователя страница 7

 Finalizing 

the 

Installation

  

(for qualified installers only)

 

7 

© Travis Industries 

4161018 

100-01436 

Installation Recommendations for Cold Environments 

If you live in the area depicted in black in the illustration to the 
right (or in Canada), we recommend the following steps be 
taken to minimize cold air infiltration. 

Insulated Chimney is Strongly Recommended 

Insulated chimney does not require cooling ducts and is 
therefore preferred for cold environments.  This is the 
number one method for improving cold weather performance.

Use “P” Trap & Insulated Duct in the Cooling Duct. 

If using air-cooled chimney, we recommend insulating the 
intake duct and putting in a “P” trap to help prevent air 
circulation when the fireplace is not in use.  A typical “P” trap 
design is shown in the illustration to the right.   

Use Bi-Metallic Damper with Air-Cooled Chimney 

If using air-cooled chimney, we recommend the use of the bi-
metallic damper.  This component (part # 250-01741) is an 18” 
section of Duravent pipe that is installed at the top of the 
chimney, directly below the cap. It has a heat-activated damper 
that helps reduce cold air from entering the cooling ducts while 
the fireplace is not in operation. 

Use Outside Air “P” Trap and Insulated Duct 

 

 

Min. 24"
Max. 48"

Min. 24"

Max. 48"

42 Apex Fireplace

 

We recommend putting in a “P” trap in the outside air duct (used to supply air to the firebox) to prevent air 
circulation when the fireplace is not in use.  A typical “P” trap design is shown in the illustration above.  In 
addition, you should insulate the outside air duct to help reduce air circulation when the fireplace is not in 
use. 

Daily Requirements for Homeowners 

HUMIDITY

 - Make sure the humidistat is set correctly.  The chart below details the correct setting for the 

temperature you are experiencing outdoors. 

Outdoor Temperature 

Recommended Humidity Controller 
Setting 

°F °C 

 

 

 

-20 -29 

15 

-10 -23 

20 

0 -18 

25 

+10 -12 

30 

+20 -7 

35 

>+20 >-7 

40 

Note: If using a humidifier, let the homeowner know that it should be shut off or turned to a lower setting 
to eliminate condensation on the front of the fireplace. 

OTHER ITEMS 

 

Make sure the bypass is shut when the fireplace is not in use. 

 

Slide the air control fully closed when fireplace is not in use. 

 

Minimize the use of exhaust fans in the home when the fireplace is not in use. 

Содержание 42 Apex





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды