Fire-Lite ACM-16ATF Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 68

background image

4. Installation

Wiring the Expander Connections

32

ACM-16ATF/ACM-32AF Manual PN 51480:A0 02/02/01

Four Position Backbox (-4 Series) or Cabinet

ACM-16 Series/AEM-16ATF

If installing one ACM-16 Series annunciator with three AEM-16ATF
expanders on the same trim plate or dress panel, perform the following steps:

• Plug one end of an Expander Ribbon Cable into connector J2 on the

annunciator module.
Place the expander module in the second position.
Connect the ribbon cable from the annunciator module to connector J3
on the expander module.

• Connect one end of a ribbon cable to connector J2 on the first expander

module.
Place the second expander module in the third position.
Connect the other end of the expander ribbon from the first expander
module to Connector J3 on the second expander module.

• Connect one end of a ribbon cable to Connector J2 on the second

expander module.
Place the third expander module in the fourth position.
Connect the other end of the ribbon cable from the second expander
module to Connector J3 on the third expander module.

ACM-32AF/AEM-32AF

If installing a second set of ACM-32AF/AEM-32AF annunciator/expander
modules in the same dress panel or trim plate, repeat the following steps for
installation of positions three and four:

• Plug terminal blocks on circuit wiring in backbox to connectors on the

second annunciator set.

Note:

A 120-ohm ELR must remain installed across the EIA-485 line at the

last annunciator on the circuit.

• Place the annunciator module in position three.

• Plug one end of an Expander Ribbon Cable into connector J2 on the

annunciator module.

• Place the expander module in the fourth position.

• Connect the ribbon cable from the annunciator module to connector J3

on the expander module.

«
...
30
31
32
33
34
...
»

Содержание ACM-16ATF





































































Отзывы:

Нет отзывов

Похожие инструкции для ACM-16ATF

Бренд: Canon Страницы: 54

Бренд: Canon Страницы: 54

Бренд: Gale Страницы: 16

Бренд: Magmaweld Страницы: 172

VEGATRENN 149A EX

Бренд: Vega Страницы: 45

Aqua-Hot AHE-100-04S

Бренд: Vehicle Systems Страницы: 19

Бренд: R-Tech Страницы: 57

Бренд: VocoPro Страницы: 28

Бренд: Watchguard Страницы: 4

Бренд: Panasonic Страницы: 16

Бренд: PrimeWeld Страницы: 23

Бренд: Razer Страницы: 16

Бренд: Electro-Voice Страницы: 2

Бренд: System Q Страницы: 52

Бренд: Cyrus Страницы: 6

Бренд: Inline Страницы: 2

Бренд: Dahua Страницы: 29

Panametrics Epoch 4 Plus

Бренд: Olympus Страницы: 188

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды