Fire-Lite ACM-16ATF Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 68

background image

ACM-32AF Series

2. Inventory

ACM-16ATF/ACM-32AF Manual PN 51480:A0 02/02/01

13

ACM-32AF Series

Control Modules

ACM-32AF

This control module contains 32 red “point active”
LEDs, a system “trouble” LED, an On-line/Power
LED, and a local piezo sounder with a
silence/acknowledge switch for audible indication
of alarm and trouble conditions at each annunciator.

Height = 8-3/8" (21.27 cm)
Width = 4-3/8" (11.11 cm).

Note:

In Canada this module must be used to

annunciate the fire alarm input points/zones only.

Expander Modules

AEM-32AF

Expands the ACM-32AF Series by 32 system points. This unit is identical
in size and frontal appearance to the control module. One expander module
can be supported by a control module providing a maximum of 64 points.

Note:

The AEM-32AF cannot be used to expand the ACM-16ATF Series control

modules.

Note:

In Canada the color red may only be used to indicate active alarm inputs. The

color yellow may be used to indicate supervisory, burglary and trouble signals, and
the color green may be used to indicate the presence of power, or an activated
output.

A

C

M-

32A

.cdr

«
...
11
12
13
14
15
...
»

Содержание ACM-16ATF





































































Отзывы:

Нет отзывов

Похожие инструкции для ACM-16ATF

Бренд: Ibiza Страницы: 24

Бренд: i3-TECHNOLOGIES Страницы: 19

Бренд: Samsung Wisenet Страницы: 16

Бренд: 4xem Страницы: 68

EasyLook PPDF17000

Бренд: Abus Страницы: 23

ELI-IP5-APTZ21-30X

Бренд: E-line Страницы: 38

Бренд: Nutek Страницы: 9

Бренд: Telwin Страницы: 164

Бренд: Akura Страницы: 11

Nexus Contractor SP-5NXC/T

Бренд: Speco Страницы: 4

Бренд: Iget Страницы: 8

MicroView MVIC-04IR-E

Бренд: ERNITEC Страницы: 31

Magnavox FW 55C

Бренд: Magnavox Страницы: 80

Бренд: Vivotek Страницы: 15

Бренд: Alecto Страницы: 12

Millermatic 212

Бренд: Miller Electric Страницы: 44

Бренд: Servodan Страницы: 6

Бренд: Fbt Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды