Fire-Lite ACM-16ATF Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 68

background image

2. Inventory

Cabinet & Panel Hardware

14

ACM-16ATF/ACM-32AF Manual PN 51480:A0 02/02/01

Cabinet & Panel Hardware

Surface-Mount Backboxes

ABS-1F

This surface mounted backbox provides for the remote
mounting of a single ACM-16ATF Series or ACM-
32AF Series annunciator in a surface-mount enclosure.
Knockouts are provided for use with 1/2" conduit. The
annunciator mounts directly to the box without a dress
plate.

Height = 8-1/2" (21.59 cm)
Width = 4-1/2" (11.43 cm)
Depth = 1-3/8" (3.49 cm).

ABS-2F

This surface mounted backbox provides for the surface mounting of an
annunciator-expander combination. Knockouts are provided for use with
1/2" conduit. The annunciator module mounts directly to the box without
a dress plate.

Height = 8-1/2" (21.59 cm)
Width = 8-15/16" (22.7 cm)
Depth = 1-3/8" (3.49 cm).

Note:

The ABS-1F and ABS-2F will not support the installation of the AKS-1

Annunciator Key Switch.

ABS-1TF

The ABS-1TF is a surface mounted backbox for mounting one ACS Series
annunciator. This backbox has an increased depth that allows mounting of
the AKS-1 Annunciator Key Switch.

Height = 9-15/16" (25.24 cm)
Width = 4-5/8" (11.75 cm)
Depth = 2-1/2" (6.35 cm).

5043

9d2.ti

f

«
...
12
13
14
15
16
...
»

Содержание ACM-16ATF





































































Отзывы:

Нет отзывов

Похожие инструкции для ACM-16ATF

Бренд: Cambridge SoundWorks Страницы: 20

Бренд: Q Acoustics Страницы: 19

Бренд: Harman Kardon Страницы: 4

Бренд: Care Call Страницы: 2

Бренд: Audio Concepts Страницы: 13

Air Live FE-200CU

Бренд: Ovislink Страницы: 3

Бренд: QSC Страницы: 4

Бренд: jablotron Страницы: 2

Бренд: Young Shin Electronics Страницы: 10

Бренд: BUCKINGHAM MFG Страницы: 5

Бренд: Takex Страницы: 8

Бренд: KEF Страницы: 2

Бренд: RoDEK Страницы: 16

Бренд: KRAMBLE INDUSTRIES Страницы: 12

Бренд: DSE Страницы: 4

Бренд: Esse-ti Страницы: 44

Бренд: Aqara Страницы: 8

Бренд: Vectaire Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды