Fiplex DHS37-R-DU Скачать руководство пользователя | Manualshive

Страница: 3 / 45

background image

DHS37-R-DU

III

About this manual

This manual describes installation, commissioning, operation and maintenance of the

Fiplex DHS37-R-DU Digital Remote

Unit

, and

Fiplex Control Software (FCS)

.

.
The first part of the manual describes the Digital Fiber DAS hardware and the second part describes the software.

Hardware and software mentioned in this manual are subjected to continuous development and improvement. Consequently,
there may be minor discrepancies between the information in the manual and the performance and design of the hardware
and software. Specifications, dimensions and other statements mentioned in this manual are subject to change without notice.

This manual or parts of it may not be reproduced without the written permission of Fiplex Communications Inc.

Infringements will be prosecuted. All rights reserved.

Copyright © Fiplex Communications Inc, Miami, 2017.

«
1
2
3
4
5
...
»

Содержание DHS37-R-DU














































Отзывы:

Нет отзывов

Похожие инструкции для DHS37-R-DU

Бренд: D-Link Страницы: 13

Бренд: Aastra Страницы: 2

Бренд: WAGO Страницы: 2

Бренд: Niveo Страницы: 155

PARTNER Voice Messaging PC Card Release 2

Бренд: Lucent Technologies Страницы: 67

USB-BRIDGEV2-EVAL

Бренд: IDT Страницы: 11

PISO-725 Series

Бренд: ICP DAS USA Страницы: 8

Бренд: Sangoma Страницы: 6

Бренд: PMD Страницы: 74

VMG5313-BXB SERIES

Бренд: ZyXEL Communications Страницы: 2

Бренд: Talent Страницы: 18

Aquaduct 240 eco

Бренд: Aqua Computer Страницы: 20

Бренд: ZyXEL Communications Страницы: 2

Бренд: Supermicro Страницы: 15

Mustang-M2AE-MX1

Бренд: IEI Technology Страницы: 58

24-Port 1000BASE-T

Бренд: Comet Labs Страницы: 44

Бренд: PRIZM Страницы: 8

Бренд: Digi Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды