6
FIGURE 1:
1. Graphic display:
The 5,7’’ colour screen displays different
screens, according to the welding mode or
settings. In weld mode the display is divided
into five principal:
Part 1:
Machine status
Part 2:
Meaning of the active buttons
(buttons 2, 3, 4, 5,6 di fig.1)
Part 3:
Size values set
Part 4:
Type of process selected
Part 5:
Indicates the values that can be set
for the various welding settings (to change
the values select using switch 10 and
confirm the selection by pressing the same
switch; the value will be highlighted in a
contrasting colour. The values can be
changed by turning the switch, to confirm
the new value press the switch again. 10).
Highlighted value: Indicates the parameter
that is being changed using switch 10.
DISPLAYS:
- When the screen comes on, the Fimer logo
will appear and the Firmware revisions will load.
CONTROL BUTTONS:
(2, 3, 4, 5,6 in fig.1)
Each control button is associated with a
specific function shown on the display.
7. SD slot:
this slot, covered with a rubber
cap, contains the SD-Card provided with the
machine; without the card, the machine will
be inactive and a warning message will
appear on the screen.
8. USB port:
only for technical assistance.
9. Knob for setting the main welding
parameter:
the main welding parameter can
be set with this knob:
Welding MMA/TIG: sets the welding current.
11.
Air grills (must never be obstructed).
12. “-” dinse front connector:
negative
pole inlet.
Connection socket TIG torch mode.
MMA Mode:
Ground clamp
MIG Mode:
Ground clamp
13.
Connector for remote control.
14. “+” dinse front connector:
positive
pole inlet.
MMA Mode:
Electrode holder
TIG Mode:
Ground clamp
MIG Mode with gas:
Not used
15. Gas Outlet:
MMA Mode:
inactive
TIG Mode:
Gas connection to the welding torch
(Internal tap positioned on TIG GAS)
MIG Mode with gas:
inactive (internal tap
positioned on MIG GAS)
16. EUROCONNECTOR (SEPARATED
TROLLEY):
quick connector for welding
torch. This connector is used to supply welding
gas to the torch, the electrical contacts of the
torch button and the welding current.
FIGURE 2:
17. ON-OFF switch:
turns the machine on
and off.
18. Input cable:
connection cable to the
mains power equipped.
19. Welding gas inlet
MMA Mode:
Not used
TIG Mode:
GAS connection to the cylinder
MIG Mode with gas:
GAS connection to the
cylinder
20. Fuse
21.Connector for supplying power to the
liquid cooling system (Optional):
Warning
the connector
contains dangerous
voltages: NEVER use it for purposes other than
those for which it was specifically designed.
Part 1
Part 2
Part 3
Part 4
Part 5
Содержание TM 236
