manualshive.com logo in svg

FibroPool FH 270, Руководство по установке

Поделиться
Скачать
FibroPool FH 270 Скачать руководство пользователя страница 11

Running Test

Inspection Before Running Test

1.

Check electrical connecors, terminal screws. Be sure all are tight

2.

Check voltage at the power supply, 208-240 volts must be observed.

3.

Check Bonding wire's tightness and attachment to the ground rod.

4.

Check plumbing connections, make sure all glued, tight and In from BOTTOM, OUT from TOP

Turn on the pump

Wait about 1 minute, for all the air to purge from the system

Turn on the heater

Push the ON OFF button on the heater, Making sure the SUNSHINE sign is on top.

ALLOW  ABOUT   5   MINUTES,   FOR   THE   FAN   TO   START   BLOWING   COLD  AIR,   CONDENSATE

WATER TO START DRIPPING. 

This is the indication of the heater working.

If all is well, leave your heater running. Your heater will only be on while your pump is ON

In  and  out   temperatures  maybe  very  close  or  even   the   same,   but   this   depends   on   many

factors including a strong pump pushing the water too fast to register.   Real indication of heating

is cold air and condensation.

V-2105 Fibropool Co LLC, Ms USA

Содержание FH 270



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды