Fibocom FM350-GL Скачать руководство пользователя страница 55

Страница: 55 / 59

FM350-GL Hardware Guide

Page 55 of 59

Antenna Type

Bands

Peak Gain

Antenna Type

Bands

Peak Gain

Monop

WCDMA B2

Monop

LTE B41

WCDMA B4

LTE B48

WCDMA B5

LTE B66

LTE B2

LTE B71

LTE B4

5G NR n2

LTE B5

5G NR n5

LTE B7

5G NR n7

LTE B12

5G NR n25

LTE B13

5G NR n30

LTE B14

5G NR n38

LTE B17

5G NR n41

LTE B25

5G NR n66

LTE B26

5G NR n71

LTE B30

5G NR n77

LTE B38

5G NR n78

In the event that these conditions cannot be met (for example certain laptop configurations or co-location

with another transmitter), then the FCC/IC authorization is no longer considered valid and the FCC ID/IC

ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible

for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/IC

authorization.

Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install

or remove this RF module in the user’s manual of the end product which integrates this module. The end

user manual shall include all required regulatory information/warning as show in this manual.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

Содержание FM350-GL

























































Результаты поиска

Содержание FM350-GL

Отзывы:

Похожие инструкции для FM350-GL

Бренды по названию

Популярные бренды

Fibocom FM350-GL, Руководство по оборудованию

Результаты поиска

Содержание FM350-GL

Отзывы:

Похожие инструкции для FM350-GL

Бренды по названию

Популярные бренды