manualshive.com logo in svg

FIBER FOX Mini 6S+, Руководство пользователя

Поделиться
Скачать
FIBER FOX Mini 6S+ Скачать руководство пользователя страница 32

30

7.2 Stabilize Electrodes

In the event of sudden change in environmental conditions, especially when the 
splicer is moved from lower altitudes to higher altitudes, the arc power may become 
unstable, resulting in higher splice loss. In such case, it takes time for arc power to 
be stabilized. In this case, stabilizing electrodes will expedite the process to set the 
arc power stable. If many tests are needed until the “Operation Complete” message 
appears in [Arc calibration], use this function as well.
Operation Procedure
① Select [Stabilize electrodes].
② Place prepared fibers into the splicer for splicing.
③ Press [SET] button, and the splicer will begin to stabilize the electrodes 
automatically in the following procedures:
• Repeat arc discharge five times to measure the arc position.
• Perform splicing rapidly.
•Perform stabilizing electrodes 20 times consecutively to precisely locate the 
electrodes position.

7.3 Diagnostic Test

has a built-in diagnostic test function that allows the user to evaluate 
several critical variable parameters with only one simple step. Perform this function 
in case of splicer operation fault.

Operation Procedure

① Select [Diagnostic Test] in [Maintenance Menu]

⑤ We recommend all users to do stabilizing electrodes and arc calibration after 
electrodes replacing to keep good splice results and splice strength (Details are 
described below).

Содержание Mini 6S+


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды