manualshive.com logo in svg

FIBER FOX Mini 6S+, Руководство пользователя

Поделиться
Скачать
FIBER FOX Mini 6S+ Скачать руководство пользователя страница 10

08

2.4 Transport and Storage Precautions

① Always avoid using hard objects to clean V-grooves and electrodes.
② Always avoid using acetone, thinner, benzol or alcohol when cleaning any part of 
the splicer, except for the places advised.
③ Use a dry cloth to remove dust and dirt from the splicer.
④ If the outside of the splicer is dirty, plunge a soft cloth into diluted neutral 
washing up liquid, wring out the cloth and clean. Dry the splicer with a dry cloth but 
DO NOT use furniture polish or other cleaning agents.
⑤ Always follow the maintenance instructions in this manual.

2.3 Maintenance and External Care Precautions

① When the splicer is moved from cold to warm environment, you should allow the 
splicer to warm up gradually. Otherwise, the condensation generated inside will 
bring harmful effects to the splicer.
② Pack the fusion splicer well for long time storage.
③ Keep the splicer clean and dry.
④ The splicer is precision adjusted and aligned. Always keep the splicer in its 
carrying case to protect from damage and dirt. Put cushion package outside the 
carrying case for long distance transportation.
⑤ Always avoid leaving the splicer in direct sunlight or expose to excessive heat.
⑥ Keep the humidity to a minimum level where the splicer is stored. The humidity 
must not exceed 95%.

        Fumes, bad smell, abnormal noise or over heat.
        Liquid or other matter falls into cabinet
        The splicer is damaged or dropped.
If any of these faults occurs, please contact our service center immediately. Leaving 
the splicer in a damaged state without any prompt measures may cause equipment 
failure, electric shock, or fire and may result in injury or death.
⑧ Do not use compressed gas or canned air to clean the splicer. They may contain 
flammable materials that could ignite during the electrical discharge.
⑨ Please use specific standard AC adapter only. Using an improper AC 
power source may cause fuming, electric shock or equipment damage and may even 
result in fire, injury or death.
⑩ Please use specific AC power cord only. Do not place any heavy objects 
on the AC power cord. Keep the power cord away from heat source. Do not modify 
the power cord. Using an improper cord or a damaged cord may cause fuming, 
electric shock or equipment damage and may even result in fire, injury or death.

Содержание Mini 6S+


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды