Festo CPX-FB38 Скачать руководство пользователя страница 98

Страница: 98 / 120

3. Diagnosis

3−8

Festo P.BE−CPX−FB38−EN en 0804NH

3.2.1

EtherCAT operating status display (LED run),
EtherCATerror(LEDError),connection status (LEDs L/A2, L/A1)

Run EtherCAT operating status (communication status)

LED (green)

Sequence

Status

Meaning/error handling

LED is off

OFF

Init

Bus node is in the the Init status (normal condi
tion after switch−on or after a restart or reboot)

LED flashes

OFF

Pre−operational

Bus node is in the pre−operational status
(network configuration)

LED
flashes 1x

OFF

Safe−operational

Bus  node  is  in  the  safe−operational  status
(e.g.due  to  a  network  disturbance).  Only  the
input  signals  (e.g.  sensor  data)  are  updated.
Outputs  and  valves  maintain  the  current  state
(signal  is  frozen").

LED lights up

OFF

Operational

Bus node is in the Operational status
(normal operating status)

LED flickers

OFF

Initialisation

Bus node carries out a restart (reboot) and is

not

yet

in the Init status (designated as Initialisation

status)

One−time short flashing (1x flash, pause, 1x flash, etc.) is designated as single flash.

Tab.3/3:

Fault diagnosis with the Run LED

Содержание CPX-FB38

























































































































Результаты поиска

Содержание CPX-FB38

Отзывы:

Бренды по названию

Популярные бренды

Festo CPX-FB38, Электронное руководство

Результаты поиска

Содержание CPX-FB38

Отзывы:

Бренды по названию

Популярные бренды