Festo CPX-FB38 Скачать руководство пользователя страница 31

Страница: 31 / 120

1. Installation

1−15

Festo P.BE−CPX−FB38−EN en 0804NH

1.3.2

Overview of connections, network connectors and cables

Bus nodes

Connections

Network connectors

Cable specification

CPX−FB38

2x  M12  socket,
D−coded,  female,
4−pin,  according  to
IEC61076−2−101,
SPEEDCON

compatible

Plug  from  Festo,  type
NECU−M−S−D12G4−C2−ET,
for  Ethernet  lines  with
cable  diameters  of
6

8mm

Cable type:

Shielded industrial Ethernet line
(at leastcategory Cat 5)

Cable length:

max.  100m  between  network  par
ticipants  (corresponding  to  spec
ifications  for  Ethernet  networks,
ISO/IEC11801  and  ANSI/TIA/
EIA−568−B)

Core cross section for max. line

length:
22AWG (for 100m link length,
based on ISO/IEC11801)

Tab.1/3:

Overview of connections, network connectors and network cables

Please note

If  installation  has  not  been  carried  out  correctly  and  if  high
baud  rates  are  used,  data  transmission  errors  may  occur
as  a  result  of  signal  reflections  and  attenuation.

Causes of transmission faults may be:

incorrect screening/shield connection

branches

transmission over long distances

unsuitable cables.

Observe the cable specification!

Refer to the manual of your controller for information
about the required type of cable.

Содержание CPX-FB38

























































































































Результаты поиска

Содержание CPX-FB38

Отзывы:

Бренды по названию

Популярные бренды

Festo CPX-FB38, Электронное руководство

Результаты поиска

Содержание CPX-FB38

Отзывы:

Бренды по названию

Популярные бренды