11
EN
Assembly of the saw blade
Fig. J
First remove the plug from the mains
before the saw blade is assembled or
replaced.
The arrow marked on the saw blade,
which indicates the direction of rotation.
Must point in the same direction as the
arrow marked on the machine, the saw
blade teeth must point downwards on
the front of the saw.
• Remove the inlay from the bench. Use a
screwdriver for this purpose.
• Turn the saw axle completely upwards (Fig.A, 5).
Remove the nut and the outside flange from the
saw axle (Fig. J, direction A).
• Now slide the saw blade over the saw axle and
now put the outside flange and the nut back.
Tighten the nut by hand.
• Now use the 2 keys: one for the flange and one
for the nut and now clamp it (Fig. J, direction B).
• Now put the inlay back in the bench and fasten
it.
Use of the mitring set-up
Fig. A
By turning the handle (4) at the front of the machine
you can adjust the saw blade to a maximum of 45°.
4. OPERATION
Switching On/Off
Fig. A (7)
• Press the switch into position ‘1’ to put your
machine into operation.
• To switch off the machine the same switch
needs to be pressed to position ‘0’.
• Always keep the mains cable away from
moving parts.
Using the height handle
Fig. A
• Turn height handle (5) clockwise to raise the
sawblade
• Turn height handle counterclockwise to lower
the sawblade
• Turn the saw blade approximately 2 mm higher
than the total thickness of the wood to be sawn.
Using mitre handle
Fig. A
• Release mitre handle (4) by turning the outer
part counter clockwise
• Use mitre handle to set the right mitre angle for
your cut by turning the inner part
• mitre handle by turning the outer part
clockwise.
Working instructions
There are two types of sawing methods:
• Lengthwise sawing
Sawing the workpiece in the length of the
wood grain.
• Cross-cutting or cutting off
Sawing off the workpiece crosswise.
If it concerns a panel, we do not usually
distinguish between the wood grain, but we name
the method where we saw off a part of the width
of the panel (lengthwise sawing) and when we cut
off the length (cross-cutting or cutting-off).
For both sawing methods one of the
fences must be used. Therefor never saw
without a fence!
Attention!
Before you start sawing, first check the
following:
1. Is the saw blade secured?
2. Are all the locking handles secured?
3. Is the fence parallel to the saw blade?
4. Is the protective cap working properly?
5. Are you wearing safety goggles?
6. Is the saw blade not rubbing against anything?
It is absolutely necessary to take these
points into consideration before you start
work!
Lengthwise sawing
• Secure the fence to the correct measuring
position and remove the cut-off guide from the
bench carriage. (Fig. I)
• Turn the saw blade approximately 2 mm higher
than the total thickness of the wood to be
sawn.
• Press the wood lightly towards the bench and
let it glide against the cut-off fence.
Содержание TSM1034
