9
EN
deformed.
39. Replace table insert when worn.
40. Only use saw blades specified by the
manufacturer that are intended for working
with wood or similar materials according to
EN847-1.
41. Take care that the selection of the saw blade
depends on the material to be cut.
42. Connect tabelsaws to a dust-collecting device
when sawing.
43. Use and correct adjustment of the riving knife
44. Use and correct adjustment of the upper saw
blade quard.
45. Take care when slotting.
Make sure, when changing the saw blade, the
blade width is not smaller and the main blade
thickness of the saw blade is not greater than the
thickness of the riving knife.
Wear personal protective equipment, these could
include:
• Hearing protection to reduce the risk of
hearing loss
• Eye protection
• Inhale respiratory protection to reduce the risk
of harmful dust
• Gloves when handling the blades and rough
materials (recommendation, saw blades, are
whenever practicable, carried in a container)
Warning! Do not use HSS blades.
• Insert the push stick in its holder when not in
use.
• Use a push stick or a push block to guide the
workpiece.
Warning! Do not use the saw for rebating
or grooving.
• Only use saw blades, whose maximum speed
is at least the speed indicated on the saw and
is suitable for the material to be cut.
• During the transport, the upper part of the saw
blade has to be covered, by the guard.
Switch off the machine immediately when you
discover:
• A defective mains plug or mains lead.
• A defective switch.
• Overheating of the machine.
• Smoke or odeur caused by scorched
insulation.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
• As a supply for this machine always use an
unloaded line and/or an extension cable with
conductors of at least 1,5 mm
2
and protected
with a 16 A fuse. Be sure that this extension
cable is not longer than 20 metres.
• This machine can be switched to the single-
phase network (230-240 V/50 Hz). If you are
in doubt about the earth of the electricity
provisions, consult an electrician first.
Power supply
• The motor is fitted with an overload switch (8).
If the table saw overloads, the overload switch
switches the equipment off automatically to
protect the table saw from overheating. If the
overload switch triggers, switch off the table
saw using the ON/OFF switch (7) and wait
until the table saw cools down. Then press the
overload switch (8) and restart the table saw.
Содержание TSM1034
