Fenix SM2000 Скачать руководство пользователя страница 13

Страница: 13 / 65

FENIX IMVICO SM2000 OPERATION MANUAL

13/65

2.3- RS-232 SERIAL INTERFACE

2.3.1- RS-232 Serial interface specifications

•

Data transmission type:

Serial

•

Synchronization:

Asynchronous

•

Flow control:

DTR/DSR control or XON/XOFF

•

Signal levels (RS232):

MARK = -3 to -15 V

Logic ‘1’/OFF

SPACE = +3 to +15 V

Logic ‘0’/ON

•

Speed:

4800, 9600, 19200, 38400 bps (bps: bits per second)

•

Data length:

7-8 bits

•

Parity:

none, even, odd

•

Stop bits:

Fixed to 1

•

Connector (printer side):

SUB-D25 female pin connector (SM2000-S)

SUB-D9 male pin connector (SM2000-U)

NOTE:

(1) Data length, speed and parity depend on the DIP switches settings (refer to section 3.3.4).

2.3.2- Change between online and offline mode

The printer is in offline mode:

1) When powering up or resetting the printer, until the printer is ready to receive data.

2) When performing the self-test.

3) When the cover is open.

4) After pressing the Paper feed button (FEED) while the paper advances.

5) When ‘out of paper’ causes the printer to stop printing.

6) During macro execution in standby mode.

7) When the power supply has a temporal abnormal voltage change.

8) When an error has occurred.

2.3.3- Assignments of RS-232 connector terminals

The assignments of the terminals of the RS-232 connector and the functions of its signals are described
in the following table:

Pin

SUB-D9

Pin

SUB-D25

Signal

name

Signal

direction (from

the printer

point of view)

Function

Frame ground

TXD

Output

Data transmission

RXD

Input

Data reception

RTS

Output

Same as DTR signal

DSR

Input

This signal indicates whether the host system is ready to
receive data.
When the XON/ XOFF control is selected, the printer does
not check this signal.

Signal ground.

Содержание SM2000


































































Результаты поиска

Содержание SM2000

Отзывы:

Похожие инструкции для SM2000

Бренды по названию

Популярные бренды

Fenix SM2000, Руководство по эксплуатации

Результаты поиска

Содержание SM2000

Отзывы:

Похожие инструкции для SM2000

Бренды по названию

Популярные бренды