Femi XXX Скачать руководство пользователя страница 15

Страница: 15 / 48

To install the safety guard with the head uplifted, place it
on the angular bearings

of the base. Then lower the

head and block the body in this position by means of the
block pin

To adjust the height of the upper work surface to obtain
desired cutting widths, follow the instructions below:

loosen the two handwheels

;

move the bearing bracket

toward the blade;

raise or lower the table using the relative knob until the

desired cutting height is reached;

tighten the two handwheels

;

3.5

ADJUSTMENT OF BEARING BRACKET (Fig.
8)

JUST FOR CIRCULAR SAW

Loosen the handwheels

and slide the bracket

, aligning

the index

on the bearing with its corresponding position

on the graduated scale on the work surface.
This position corresponds to the actual distance of the
bearing bracket rest from the centre line of the blade.

3.6

WEDGE REGULATION

To ensure the dividing wedge is in the correct position,
keep it at a distance of between 3mm - 8mm from the
tooth of the blade. Should this not be the case, loosen the
screw which holds it attached to the arm and move it to the
aforementioned distance

(Fig. 16).

USE

After having performed all the above procedures and
operations, you may begin cutting.

HAZARD: Always keep hands away from the
cutting area and do not try to approach it when
the machine is running.

4.1

USE AS A CUTTING-OFF MACHINE
(cutting on the lower work surface) (Fig. 9)

Release the head, by unscrew the block pin

Raise the machine head as far as possible.

Secure the workpiece firmly against the angular

bearings

of the base with your left hand, thus

ensuring absolute immobility during cutting.

Put your right hand on the handgrip

and press the

button

in order to release the head.

Actuate the motor by pressing first the main switch

release device

and then the main switch start

button

on the handgrip.

Lower the head and gradually bring the blade into

contact with the workpiece.

Complete cutting and raise the head to its original

position.

Turn off the motor by release the main switch button

ADJUSTING (Fig. 4-5-6-7-8)

HAZARD: All the adjustment procedures
illustrated below must be performed when the
machine’s engine is off.

3.1

ADJUSTMENT OF CUTTING ANGLE-HEAD
ROTATION (Fig. 4)

This mitre-saw can cut both to the left and to the right.
The pre-set positions are: 15° - 22°30' - 30° - 45° and 50°.
To position the machine as above, loosen the handwheel

, release the machine head by pushing the lever

downwards and rotate the rotary support by using the
handgrip

The head will automatically stop each time the index

in alignment with the corresponding position indicated on
the graduated plate.
For all intermediate positions, once the the index is in
alignment with the position on the plate, block the rotating
bearing by means of the handwheel

3.2

ADJUSTMENT OF CUTTING ANGLE - HEAD
ANGLE (Fig. 5)

The machine head can be tilted to a maximum of 45° to the
left.
Release the knob

at the rear of the machine and tilt the

head until it comes into contact with the clamp at 45°
(calibrated upon inspection).
For all other intermediate positions, align index

on the

rear of the head with the corresponding position marked on
the graduated scale

of the swivel joint.

HAZARD:
During double angle cutting (rotation plus head
tilting) hold the work piece securely to the
machine using the right hand and guide the
lowering of the head with the left hand (Fig. 17).

3.3

ADJUSTMENT/INSTALLATION OF BAR CLAMP
(Fig. 6)

To cut work pieces of the same length, use the bar clamp
supplied in order to avoid repeating the same measuring
procedure more than once.
Screw the bar

into the hole in the base and block it with

the dowel

: loosen the handwheel

and position the

clamp

at the appropriate distance from the blade; then

tighten the handwheel

3.4

ADJUSTMENT HEIGHT OF UPPER WORK
SURFACE (Fi.g 7)

JUST FOR CIRCULAR SAW

HAZARD: When working on the upper surface,
it is absolutely necessary to install the lower
safety guard supplied.