Femi XXX, Инструкция по эксплуатации и техническому обслуживанию

Страница: 14 / 48

14
EN
2.4 POSITION/WORK STATION (Fig. 2-3)
Place the machine on a work bench or on a sufficiently flat
base/ pedestal to ensure the best possible stability. Should
you wish to attach the machine to a workbench, you will
need the relative accessories which must be applied to the
support feet. These are available as an optional.
Bearing in mind ergonomic criteria, the ideal height of the
bench or of the base should be such that the base surface
or the upper work surface is between 90 and 95 cm. from
the ground
(see Fig.2) .
Always ensure that there is at least 80 cm. of manoeuvring
space in all directions around the machine in order to perform
all necessary cleaning, maintenance and adjustment
operations safely with a sufficient amount of space
available
(see Fig. 3) .
CAUTION; Ensure the machine is placed in a
suitable position both in terms of environmental
conditions and lighting.
Always bear in mind that general environmental
conditions are of fundamental importance to
prevent accidents.
2.5 ELECTRICAL CONNECTIONS
Check that the electrical system to which the machine is
connected is earthed in compliance with current safety
regulations and that the current socket is in perfect condition.
The electrical system must be fitted with a magnetothermal
protective device to safeguard all conductors from short
circuits and overload.
The selection of this device should be in line with the
following electrical specifications stated on the motor.
NOTE: Your mitre-saw’s electrical system is
equipped with an undervoltage relay which
automatically opens the circuit when the voltage
falls below a minimum pre-established limit and
which prevents the self-reset of machine
functions when voltage returns to normal levels.
If the machine stops involutarily, do not be
allarmed. Make sure that there has not been a
voltage failure in the electrical system.
1.9 MACHINE DESCRIPTION (Fig.1)
The mitre-saw machine consists of three basic parts : the
machine body complete with motor
6 which is integrated
into lower part 3 by means of the joint 4 and the swivel
support 5 , and the upper work unit consisting of the work
table 15 , the rest square 17 and the movable blade cover
16 .
The base 3 is used as rest when cutting and butting
operations have to be carried out in the different available
angles; the upper table is used as rest when trimming or
sectioning wood tables of huge dimensions and, in particular,
when cutting wood along grain.
Legend Fig. 1
1
- Control handgrip A -Trademark plate / CE plate
2 - Main switch start button B -Accident-prevention plate
3 - Base C - Specification plate
4 - Body/base swivel joint
5 - Rotating bearing
6 - Motor
7 - Blade
8 - Lever to unblock graduation
9 - Button to unblock body descent
10 - Permanent blade shield
11 - Movable blade shield
12 - Bar clamp shaft
13 - Dust exhaust manifold
14 - Main switch release device
15 - Upper work surface
16 - Movable upper safety guard
17 - Bearing bracket
18 - Support feet
19 - Transport locking pin
20 - Angle rest at 90°
21 - Main switch locking device
2 INSTALLATION
2.1 REMOVAL OF PACKAGING
Remove the box used to protect the machine during
transportion and keep it intact for future transportation and
storage.
2.2 HANDLING
This mitre-saw is small and light and, therefore, can be
easily handled by one person alone by locking the
transportation block by means of the pin
19 and by lifting
the machine by means of the control handgrip 1 .
2.3 TRANSPORTATION
To transport the machine, place it in the box it was in when
purchased. Ensure it is placed in the correct position indicated
by the arrows on the packaging.
Pay careful attention to the ideograms printed on the box
as they provide all necessary information for palletization
and stacking of boxes.
Tying the load down with ropes or safety belts is
recommended during transportation to stop the load from
sliding or falling.