PRODUCT MAINTENANCE
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust causing the motor to run
even if there is no paper present
(Note: two paper detection sensors are located in the center of the paper entry)
.
TO CLEAN THE SENSORS
Turn off and unplug
shredder
Locate Auto-start
infared sensor
Using cotton swab, wipe
away any contamination
from the paper sensors
Dip cotton swab in
rubbing alcohol
3
AUTO
AUTO
AUTO
1
2
4
ENGLISH
Models 125Ci/125i
All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive
noise when shredding and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you
empty your waste bin.
OILING SHREDDER
15
15
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
*Apply oil across entry
1
4
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
PREVENTIVE MAINTENANCE & ACCESSORIES
TROUBLESHOOTING
Press and hold forward
( ) 2-3 seconds
AUTO
AUTO
AUTO
2
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator
will remain illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about
the
continuous operation and recovery time for this shredder.
Bin Full: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36054.
Bin Open: The shredder will not run if the bin is open. When illuminated, close the bin to resume shredding.
Remove Paper: When illuminated, press reverse (
) and remove paper. Reduce paper quantity to an acceptable amount and refeed into paper entry.
SafeSense
®
Indicator: If hands are too close to the paper entry, the SafeSense
®
indicator will illuminate and the shredder will stop shredding. If SafeSense
®
is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding.
LIMITED PRODUCT WARRANTY
5
Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of
defects in material and workmanship and provides service and support for 2 years from the date
of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to be
free from defects in material and workmanship for 20 years from the date of purchase by the
original consumer. If any part is found to be defective during the warranty period, your sole and
exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective
part. This warranty does not apply in cases of abuse, mishandling, failure to comply with product
usage standards, shredder operation using an improper power supply (other than listed on the
label), or unauthorized repair. Fellowes reserves the right to charge the consumers for any
additional costs incurred by Fellowes to provide parts or services outside of the country where the
shredder is initially sold by an authorized reseller. ANY IMPLIED WARRANTY, INCLUDING THAT OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION
TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable
for any consequential or incidental damages attributable to this product. This warranty gives you
specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide,
except where different limitations, restrictions, or conditions may be required by local law. For
more details or to obtain service under this warranty, please contact us or your dealer.
CLEANING AUTO-START INFRARED SENSORS
125Ci_125i_406088_RevF_19L_072015.indd 4-5
7/20/15 10:14 AM
