Felisatti PF82/900M, Руководство по эксплуатации

Страница: 6 / 69

TECHNICAL DATA
Planer PF82/900M
Nominal voltage V~ 230
Rated current frequency Hz 50-60
Nominal power W 900
No-load speed min-1 13000
Planing depth mm 0-3
Planing width mm 82
Rebate’s depth mm 0-25
Weight according to procedure
ЕРТА
01/2003 Kg 3.2
Read the operating instructions
Protection category II power tool; double
insulated
In accordance with essential applicable
safety standards of European directives
Customs Union conformity mark
In accordance with essential applicable
safety standards of Russian Federation
Wear eye protection
Wear ear protection
n
Rate speed of cutter block, /min
B Planing width, mm
H Planing depth, mm
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the tool is used with care and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual
. Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A
Safety push button switch (Fig. 2)
B On-/off switch (Fig. 2)
D Support foot (Fig. 3)
E
Drive wheel (Fig. 4)
F Toothed belt (Fig. 4)
G Idler pulley (Fig. 4)
H Vertical depth graduated scale (Fig. 3)
I
Side end-stop immobilisation control (Fig. 2)
J Circular depth graduation scale (Fig. 1 and 2)
K Depth graduation handle (Fig. 2)
L Lateral stop (Fig. 2a)
M Sawdust extraction (Fig. 2)
N Cope depth end-stop (Fig. 3)
O Blade replacement screws (Fig. 3, 5 and 6)
P
Guide slot (Fig. 3 and 6)
Q Toothed belt cover (Fig. 2 and 4)
R Toothed belt cover screw (Fig. 2)
S Mobile plate (Fig. 2 and 3)
T Dust suction adapter (Fig. 3)
U Base plate (Fig. 3)
V
Side stop locking set square (Fig. 2a)
W Side stop regulation of the wing nut (Fig. 2a)
Y
Depth stop fixing wing nut (Fig. 3)
EQUIPMENT
-
Hand electric plane
-
Dust suction adapter
-
Hexagonal key
-
Lateral stop
-
Depth end-stop
-
Operating instructions with safety instructions
-
Warranty
BRIEF DESCRIPTION
This tool has been designed to rout wood and
similar materials, to plane irregular surfaces and to
cant off edges.
Inbuilt block permits to perform the following functions:
-
Soft start;
-
Maintenance of practically constant normal speed till
development of nominal power;
-
Overload protection by means of current cutoff in case
of engine overload; in this case the tool is switched off
and then switched on only after relief of pressure on
cutter block.
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is
correct: it must be the same as that on the specifica-
tion label.
START UP
WARNING! Only plug in when machine is switched off.
Press the locking button A , and squeeze the trigger in
the on/off switch B . When the on/off switch is released,
the machine stops.
For safety reasons, it is not possible to lock On/Off
switch
B , instead it has to be pressed while the machine
is being used.
OPERATING INSTRUCTIONS
WARNING! Don’t load the power tool till its stop.
WARNING! Fix the work part if its own weight
doesn’t provide stable position.
1. Planing depth
WARNING!
Always unplug the machine before carrying
out work on it.