Fein AStx649-1, Оригинальное руководство пользователя

Страница: 16 / 130

16
en
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles
from materials containing stone, paint solvents, wood
preservatives, antifouling paints for vessels, can trigger
allergic reactions to the operator or bystanders and/or
lead to respiratory infections, cancer, birth defects or
other reproductive harm. The risk from inhaling dusts
depends on the exposition. Use dust extraction matched
appropriately for the developing dust, as well as personal
protective equipment and provide for good ventilation of
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of sanding dust
and chemical materials can self-ignite under unfavourable
conditions or cause an explosion. Avoid sparking in the
direction of the dust collector as well as overheating of
the power tool and the materials being sanded, empty the
dust collector/container in time, observe the material
manufacturer’s working instructions, as well as the rele-
vant regulations in your country for the materials being
worked.
Operating Instructions.
Guide the power tool toward the work piece only
when switched on.
Guide the power tool uniformly and with light feed in the
cutting direction. Excessive feed reduces the tool life of
the application tools.
Stroke adjustment:
– low stroke rate for working aluminium and plastics,
– high stroke rate for working steel.
To increase the tool life of the saw blade when sawing
metal, it is recommended to use a lubricating agent:
– for cuts in steel sheet: Cutting oil,
– for cuts in aluminium: Petroleum.
As an alternative, cutting paste can also be applied to the
cutting line.
Using the recommended clamping
devices.
Clamping fixture 9 07 02 001 00 1
For pipes with diameters to 159 mm, use the clamping
fixture 9 07 02 001 00 1.
– Place the clamping chain around the work piece and
insert the hooks of the grabber in the clamping chain.
– Tension the chain with the clamping-fixture handle.
– Mount the hacksaw to the retaining bolt (see “Mount-
ing the clamping fixture”).
The clamping head is readjustable for saw cuts and can be
used for angle cuts.
Clamping fixture 9 07 02 004 00 6
For large pipes with diameters from 100 mm to 325 mm,
use the clamping fixture 9 07 02 004 00 6 as well as saw
blades with lengths of 500 mm or 600 mm, and a thick-
ness of 2 mm. With the extension chain
3 02 31 003 00 3 (bolts 3 02 16 130 00 4), pipes with
diameters to 440 mm can also be cut.
Clamping fixture 9 06 06 002 00 9
When cutting pipes with diameters to 325 mm with the
1.6 mm thick and 530 mm long saw blade, use the saw
blade guide 9 06 06 002 00 9.
– With the auxiliary handle removed, mount the saw
blade guide to the mounting hole of the gear head.
Clamping fixture 9 07 02 003 00 8
To cut profiled sections to a width of 310 mm and a
height of 550 mm, use the clamping fixture
9 07 02 003 00 8. Its design corresponds to that of a par-
allel vice. The clamping jaws and the clamping head are
adjustable.
Clamping fixture 9 07 02 005 00 0
When cutting pipes and round stock with outside diam-
eters from 80 to 400 mm, use the clamp and feed device
9 07 02 005 00 0 to guide the hacksaw. A safety clutch
limits the duration that the saw blade is engaged and thus
increases tool life. For proper handling, please refer to
Instruction Manual 3 41 00 898 06 6.
Support for free hand working 3 27 14 062 02 3
To saw materials such as corrugated sheet, use the sup-
port for free hand working 3 27 14 062 02 3.
Remove the auxiliary handle and mount the support for
free hand working to the hacksaw via the clamping head
and the two gear head mounting holes for the auxiliary
handle. The saw blade goes through the opening.
Repair and customer service.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.
The total insulation of the power tool can be impaired.
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air.
When the power tool’s power cord is damaged, it must
be replaced by FEIN or by an authorized FEIN Service
Agent, in order to avoid hazardous situations.
The current spare parts list for this power tool can be
found in the Internet at www.fein.com.
If required, you can change the following parts yourself:
Auxiliary handle, application tools
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer’s warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. FEIN GmbH, C-DB_IA,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
OBJ_BUCH-0000000078-001.book Page 16 Monday, June 25, 2012 2:32 PM