FEIG ID CPR60 Скачать руководство пользователя страница 4

IDENTIFICATION 

ID CPR60 

 

 

 

 

Page 4 of 22 

 

 

 

 

1  Safety Instructions 

 

The device may only be used for the intended purpose designed by for the manufacturer. 

 

The operation manual should be conveniently kept available at all times for each user. 

 

Unauthorized  changes  and  the  use  of spare  parts  and  additional  devices  which  have  not  been  sold  or 
recommended  by  the  manufacturer  may  cause  fire,  electric  shocks  or  injuries.  Such  unauthorized 
measures shall exclude any liability by the manufacturer. 

 

The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid for the 
device. The manufacturer shall not be held legally responsible for inaccuracies, errors, or omissions in the 
manual or automatically set parameters for a device or for an incorrect application of a device. 

 

Repairs may only be executed by the manufacturer. 

 

Installation, operation, and maintenance procedures should only be carried out by qualified personnel. 

 

Use of the device and its installation must be in accordance with national legal requirements and local 

electrical codes. 

 

When working on devices the valid safety regulations must be observed. 

 

Before touching the device, the power supply must always be interrupted. Make sure that the device is 
without voltage by measuring. The fading of an operation control (LED) is no indicator for an interrupted 
power supply or the device being out of voltage! 

 

Special advice for wearers of cardiac pacemakers: 
Although this device doesn't exceed the valid limits for electromagnetic fields you should keep a 
minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in the 
immediate proxi

mity of the device’s antenna for any length of time. 

 

 

 

 

Содержание ID CPR60























Отзывы: