manualshive.com logo in svg

Feig Electronic ID LRU500i-BD Series, Руководство по установке

Поделиться
Скачать
Feig Electronic ID LRU500i-BD Series Скачать руководство пользователя страница 25

IDENTIFICATION 

ID LRU500i 

5  Terminals 

 

 

Installation 

Page 25 of 35 

 

It must be ensured that no configuration page (CFG page) is password protected in the reader. If 
configuration pages are password protected, the configuration file will not be copied onto the reader. This 
also applies if individual configuration parameters contain values out of the permissible range. 
After successful completion of the USB actions the red status LED will go out and the green status LED will 
start flashing again. After the red status LED went out the USB flash drive can be disconnected. In case of 
an error the red status LED will start flashing until the USB flash drive is removed.

 

 

NOTE: 

Connecting a USB flash drive during a running operation of the reader may overwrite an existing 

configuration file stored on the USB memory stick (See chapter 5.9.3 Storing the Reader 

Configuration on a USB Flash Drive on page 24.). 

 

 

 

Содержание ID LRU500i-BD Series




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды