Federal Signal Corporation Valor VALR44 Скачать руководство пользователя страница 10

Страница: 10 / 44

Valor

Light Bar

Federal Signal

www.fedsig.com

An Overview of the Valor

Light Bar

An Overview of the Valor Light Bar

The Valor Light Bar is a single-level LED light bar with ROC™ (Reliable On-Board

Circuitry) and Solaris® LED technologies. ROC™ eliminates approximately 85 percent

of potential failure points by incorporating a printed circuit board (PCB) in one

assembly to substantially reduce the number of electrical connections. Solaris S2 LED

modules use offset, complex reflector surfaces for accurate beam-shaping and the

highest optical efficiency. The reflectors’ overlapping, 360-degree lighting eliminates

weak spots and provides off-axis warning around the light bar. The light bar is shaped

to provide maximum intersection warning, the most dangerous situation in moving

traffic.

LED Lights, Colors, and Flash Patterns

The light bar’s internal microprocessor supplies three priority operational modes

and a library of 27 flash patterns. To increase the safety of officers, pedestrians, and

motorists, the light bar has standard front and rear cutoff, dimming, and intersection

warning. Bright white LED takedown and alley lights that are horizontally adjustable

are also available with the HotFoot™ configured option.
Multi-color heads are available with up to three different colored LEDs, eliminating the

loss of primary warning colors in takedown, alley, and directional warning positions.

Individual Valor lightheads can flash between red, blue, amber, or white.

Modular Connector System

The Valor Light Bar has a waterproof (IP67) external connector system for power and

communication to allow removal of the light bar from the vehicle without opening the

light bar or the vehicle hood. The Valor is protected against reversed polarity damage.

The Valor Light Bar may be installed in any vehicle with a 12-volt negative ground

electrical system.

Controller Options

Flash patterns are controlled through the light bar’s CAT5 communication cable. The

cable connects to the Serial Interface Module (Part Number 8583446), the Federal

Signal Six-Button Serial Controller (Part Number 8623133), the Three-Button Serial

Controller (Part Number 8623141), or the SmartSiren Series Platinum System or the

System control head only.
With the Serial Interface Module, the Valor Light Bar can be activated by Federal

Signal light bar controllers, SignalMaster directional-light controllers, or by individual

low-current switch boxes.

Содержание Valor VALR44












































Результаты поиска

Содержание Valor VALR44

Отзывы:

Похожие инструкции для Valor VALR44

Бренды по названию

Популярные бренды

Federal Signal Corporation Valor VALR44, Инструкция по установке, обслуживанию и ремонту

Результаты поиска

Содержание Valor VALR44

Отзывы:

Похожие инструкции для Valor VALR44

Бренды по названию

Популярные бренды