manualshive.com logo in svg

Federal Signal Corporation Valor FSJoin, Инструкция по установке, обслуживанию и ремонту, Страница: 39 / 40

Поделиться
Скачать
Federal Signal Corporation Valor FSJoin Скачать руководство пользователя страница 39

39

Installation, Maintenance, and Service Manual 

Federal Signal 

www.fedsig.com

Getting Technical Support and Service

After servicing the light bar, perform the Light Bar Test to ensure that all LEDs light 

properly by following these steps:

1. 

Apply 12 Vdc (+BAT) to the Light Bar Test control wire (black/white/red) from the 

Interface Module.

2. 

After all LEDs flash in sequence, the Takedown and Alley lights flash.

3. 

Remove 12 Vdc from the Light Bar Test control wire.

Testing the Steady Burn LEDs (HotFoot Only)

The Steady Burn LEDs are factory configured per the customer order for one of these 

options:

•  No Steady Burn (the LEDs flash with the pattern)
•  Driver-side Steady Burn
•  Driver- and passenger-side Steady Burn

1. 

Apply 12 Vdc (+BAT) to the red/white control wire for the Steady Burn LEDs and a 

control wire for Mode 1, 2, or 3 (Table 4 on page 14). The LEDs light and stay on 

(default setting).

2. 

Remove 12 Vdc from the Mode and Steady Burn control wires.

Getting Technical Support and Service

For technical support and service, please contact:
Service Department

Federal Signal Corporation

Phone: 1-800-433-9132

Email: [email protected]

www.fedsig.com

Getting Repair Service

The Federal Signal factory provides technical assistance with any problems that 

cannot be handled locally. 
Any units returned to Federal Signal for service, inspection, or repair must be 

accompanied by a Return Material Authorization (RMA). Obtain a RMA from a local 

Distributor or Manufacturer’s Representative. 
Provide a brief explanation of the service requested, or the nature of the malfunction. 
Address all communications and shipments to the following: 
Federal Signal Corporation

Service Department 

2645 Federal Signal Drive 
University Park, IL 60484-3167

Содержание Valor FSJoin









































Отзывы:

Нет отзывов