Federal Signal Corporation Valor FSJoin Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 40

Federal Signal Corporation Valor FSJoin Скачать руководство пользователя страница 31

31

Installation, Maintenance, and Service Manual

Federal Signal

www.fedsig.com

Maintaining and Servicing the Valor

Maintaining and Servicing the Valor

This chapter describe how to maintain and service the Valor light bar. Establishing

a regular maintenance and inspection schedule extends the life of the light bar and

ensures safety. For service, support, or replacement parts, contact the Federal Signal

Service Department at 1-800-433-9132, 7 a.m. to 5 p.m., Monday through Friday (CT).

See Table 7 on page 40 for replacement parts and part numbers.

SHOCK HAZARD: Disconnect ALL power to the light bar before any

maintenance is performed. Failure to do so may result in property damage,

serious injury, or death.

BURN HAZARD: After prolonged operation, the unit gets hot and can cause

burns. Do not touch the unit while or shortly after it has been operating.

Cleaning the Light Bar Lens

CRAZING HAZARD: Crazed, cracked, or faded domes or reflectors reduce the

light output and the effectiveness of the lighting system. Tops or reflectors

showing this type of aging must be replaced. Failure to follow this warning

may result in bodily injury or death to you or others.

CLEANING SOLUTION WARNING: The use of cleaning solutions, such as

strong detergents, solvents, and petroleum products, can cause crazing

(cracking) of the domes and reflectors. Failure to follow this warning can

damage the domes and reflectors and may result in bodily injury or death to

you or others.

To clean the light bar lens:

1.

Rinse the lens with lukewarm water to loosen dirt and debris.

2.

Use a mild detergent, lukewarm water, and a soft cloth to gently clean the lens.

To avoid damaging the finish, do not use heavy pressure or caustic, abrasive, or

petroleum-based cleaners.

3.

Rinse and dry the lens with a soft cloth to prevent water spotting.

4.

To remove fine scratches and haze, use a soft cloth and a high quality automotive

paste cleaner/wax that is non-abrasive.

«
...
29
30
31
32
33
...
»

Содержание Valor FSJoin









































Отзывы:

Нет отзывов