manualshive.com logo in svg

Federal Signal Corporation Valor FSJoin, Инструкция по установке, обслуживанию и ремонту, Страница: 38 / 40

Поделиться
Скачать
Federal Signal Corporation Valor FSJoin Скачать руководство пользователя страница 38

38

Valor

®

 Light Bar 

Federal Signal 

www.fedsig.com 

Maintaining and Servicing the Valor

Problem

Corrective Action

The light bar has a delayed 

response to being shut off

•  Ensure that the connections on the Serial Interface Module are kept 

separate from strobe supplies. 

•  Check all the ground connections, especially on the Serial Interface 

Module.

A Flash Takedown/Alley light stays 

on with ignition power applied

•  Ensure there is no voltage on the corresponding control wire.
•  To see if the ROC board is bad, swap it with a similar board. 
•  Swap the cables on the light bar controller outputs with a known 

good output. If the problem moves to another halogen light, send 

the light bar controller to Federal Signal for repair.

Takedown/alley lights work, but 

Flash Takedown/Alley lights do not 

work

•  Ensure that 12 Vdc is applied to the takedown and alley (red/black) 

control wire.

•  Check the 12 Vdc power and negative ground connections to the 

light bar to ensure there is enough current.

Only one takedown light turns on

•  Check the connections from the light bar controller to the ROC 

boards and ensure they are in the proper locations.

SignalMaster LEDs do not light

•  Check the switch settings on the Serial Interface Module. Ensure 

they are both set for the correct operation. 

•  Ensure that Switch 4 on SW2 is in the correct position for the 

selected operation on the Serial Interface Module and ignition 

power was removed and reapplied.

•  Check the connections at the SignalMaster controller. If the 

controller is a model SS2000SM, ensure that the connector has 

power and the ground is connected to pins 10 and 11 on the 

SignalMaster plug.

Quick Testing the Valor with the Light Bar Test

LIGHT HAZARDS: To be an effective warning device, this product produces 

bright light that can be hazardous to your eyesight when viewed at a close 

range. Do not stare directly into this lighting product at a close range or 

permanent damage to your eyesight may occur.

IMPORTANT:

 Ensure that SW2 Switch 3 in the Serial Interface Module is in the up 

position for the Light Bar Test. The down position is ON for the Scene Light, Right option 

in light bars with Spectralux Technology (Valor and Valor). For the scene light control 

wires see Figure 5 on page 24 or Figure 6 on page 25.

NOTE:

 The Light Bar Test does not test the optional Steady Burn LEDs. To test and 

configure these LEDs, see “Testing the Steady Burn LEDs (HotFoot Only)” on page 

39.

Содержание Valor FSJoin









































Отзывы:

Нет отзывов