background image

Safety Messages for Installers and Operators

5

Installation and Maintenance Manual 

Federal Signal 

www.fedsig.com

Safety Messages for Installers and Operators

For your safety, read and understand this manual thoroughly before installing, 

operating, and servicing the Pathfinder siren amplifier/relay module. The safety 

messages presented in this chapter and throughout the manual are reminders 

to exercise extreme care at all times. In addition, read and understand the 

safety instructions to installers (doc. no. 256A692), and keep it close at hand for 

reference. 
To download copies of this manual, go to www.fedsig.com or call the Federal Signal 

Service Department at 1-800-433-9132 (708-534-3400) 7 a.m. to 5 p.m., Monday 

through Friday (CT).

Safety Messages to Installers of Sound/Light Systems

People’s lives depend on your proper installation and servicing of Federal Signal 

products. It is important to read and follow all instructions shipped with this 

product. Listed below are some other important safety instructions and precautions 

you should follow:

Before Installation
Qualifications

•  To properly install an electronic siren, you must have a good understanding 

of automotive electrical procedures and systems, along with proficiency in 

the installation and service of safety warning equipment. Always refer to 

the vehicle’s service manuals when performing equipment installations on a 

vehicle.

Sound Hazards

•  Your hearing and the hearing of others, in or close to your emergency vehicle, 

could be damaged by loud sounds. This can occur from short exposures to very 

loud sounds, or from longer exposures to moderately loud sounds. For hearing 

conservation guidance, refer to federal, state, or local recommendations. OSHA 

Standard 1910.95 offers guidance on “Permissible Noise Exposure.”

•  All effective sirens and horns produce loud sounds (120 dB) that may cause 

permanent hearing loss. Always minimize your exposure to siren sound and 

wear hearing protection. Do not sound the siren indoors or in enclosed areas 

where you and others will be exposed to the sound.

•  Federal Signal siren amplifier/relay modules and speakers are designed to 

work together as a system. Combining a siren and speaker from different 

manufacturers may reduce the warning effectiveness of the siren system and 

may damage the components. You should verify or test your combination to 

make sure the system works together properly and meets federal, state and 

local standards or guidelines.

During Installation

•  Do NOT get metal shavings inside the product. Metal shavings in the product 

can cause the system to fail. If drilling must be done near the unit, place an ESD 

Содержание Pathfinder Siren Series





















Отзывы: