manualshive.com logo in svg

Federal Signal Corporation Legend LGD, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Federal Signal Corporation Legend LGD Скачать руководство пользователя страница 8

Safety Messages

8   

Legend LGD and Legend LPX Light Bars 

Federal Signal

 www.fedsig.com

•  Because vehicle roof construction and driving conditions vary, do not drive a 

vehicle with a magnetically mounted warning light installed. The light could fly 

off the vehicle causing injury or damage. Repair of damage incurred because of 

ignoring this warning shall be the sole responsibility of the user.

•  To avoid denting the roof of the vehicle, place the light bar mounting feet as 

close to the outer edge of the roof as possible.

•  Roof damage can occur if the hook adjustment bolts are overtightened. Torque 

each hook adjustment bolt 6 ft-lb to 7 ft-lb. Install keeper plates,

•  Locate the light system controls so the VEHICLE and CONTROLS can be 

operated safely under all driving conditions.

After Installation or Service

•  After installation, test the light system to ensure that it is operating properly.
•  Test all vehicle functions, including horn operation, vehicle safety functions, and 

vehicle light systems, to ensure proper operation. Ensure that the installation 

has not affected the vehicle operation or changed any vehicle safety function 

or circuit.

•  Scratched or dull reflectors, mirrors, or lenses will reduce the effectiveness 

of the lighting system. Avoid heavy pressure and the use of caustic or 

petroleum-based products when cleaning the lighting system. Replace any 

optical components that may have been scratched or crazed during system 

installation.

•  Do not attempt to activate or deactivate the light system control while driving in 

a hazardous situation.

•  Frequently inspect the light system to ensure that it is operating properly and is 

securely attached to the vehicle.

•  After installation and testing are complete, provide a copy of these instructions 

to instructional staff and all operating personnel.

•  File these instructions in a safe place and refer to them when maintaining and/or 

reinstalling the product.

•  Holding power of magnetic mounting systems is dependent upon surface 

finish, surface flatness, and thickness of the steel mounting surface. Therefore, 

to promote proper magnetic mounting:

•  Mounting surface and magnets must be kept clean, dry, and free of foreign 

particles that prevent good surface contact.

•  Ensure that mounting surface is flat.
•  A magnet mounting system should not be used on vehicles with vinyl tops.
•  Avoid quick acceleration and hard stops to prevent sliding of light assembly 

on mounting surface.

Failure to follow all safety precautions and instructions may result in property 

damage, serious injury, or death.

RETAIN AND REFER TO THIS MESSAGE

Содержание Legend LGD





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды