manualshive.com logo in svg

Federal Signal Corporation Legend LGD, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Federal Signal Corporation Legend LGD Скачать руководство пользователя страница 24

Preparing the Legend for Installation

24   

Legend LGD and Legend LPX Light Bars 

Federal Signal

 www.fedsig.com

To change from HIGH to TAP II or 8-SECOND TIMEOUT:

1. 

Unplug the 24-pin harness from the Serial Interface Module.

2. 

On the Serial Interface Module, set Switch 7 and Switch 8 on SW-2 to select 

a method of operation (Figure 2 on page 21 and Table 11.) Each setting is 

independent of the other. 

3. 

Plug the 24-pin harness into the Serial Interface Module.

Table 11  Switch settings for INTERSECTION operation

Operational Settings

SW-2
SW7

SW8

HIGH (+BAT maintained)

OFF (up)

OFF (up)

TAP II (+BAT, push on/push off )

ON (down)

OFF (up)

8-SECOND TIMEOUT (activated by +BAT)

OFF (up)

ON (down)

FRONT/REAR ENABLE or CUTOFF

The operational setting for FRONT/REAR ENABLE or CUTOFF must be 

programmed after MODE and INTERSECTION. The default setting is for CUTOFF 

in which the FRONT or REAR LEDs turn off when 12 Vdc (+BAT) is applied to their 

control wires. In contrast, FRONT/REAR ENABLE turns on these LED modules 

when +BAT is applied to their control wires. Both FRONT and REAR share the same 

operational setting and are not independent. 
To program for FRONT/REAR ENABLE or CUTOFF: 

1. 

Unplug the 24-pin harness from the Serial Interface Module.

2. 

On the Serial Interface Module, move Switch 1 on SW-2 to:

•  the down (on) position for Front/Rear Enable.
•  the up (off) position for Front/Rear Cutoff.

3. 

Plug the 24-pin harness into the Serial Interface Module.

NOTE:

 When set to ENABLE, 12 Vdc must be applied to a MODE control wire and the 

FRONT and/or REAR ENABLE control wire for the light bar to operate.
In a typical installation, if you want only the REAR LED modules to flash in MODE 1, 

set the operation for ENABLE. Connect the green/white and blue/white control 

wires to the MODE 2 connection and the orange/black and blue control wires to 

the MODE 1 connection.

Exiting Program Mode

When you are finished programming patterns, switch the Serial Interface Module 

from Operation Mode to Program Mode.

1. 

Unplug the 24-pin harness from the Serial Interface Module.

2. 

On the Serial Interface Module, move SW-2 Switch 6 to the up (OFF) position.

Содержание Legend LGD





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды