manualshive.com logo in svg

Federal Signal Corporation Legend LGD, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Federal Signal Corporation Legend LGD Скачать руководство пользователя страница 7

Safety Messages

7

Installation, Operation, and Service Manual 

Federal Signal 

www.fedsig.com

•  Never attempt to install aftermarket equipment that connects to the vehicle 

wiring without reviewing a vehicle wiring diagram available from the vehicle 

manufacturer. Ensure that your installation will not affect vehicle operation or 

mandated safety functions or circuits. Always check the vehicle for proper 

operation after installation.

•  The lighting system components, especially light bulbs, strobe tubes, LEDs, and 

the outer housing, get hot during operation. Be sure to disconnect power to the 

system and allow the system to cool down before handling any components of 

the system.

•  Do not mount a radio antenna within 18 inches (45.7 cm) of the lighting system. 

Placing the antenna too close to the lighting system could cause the lighting 

system to malfunction or be damaged by strong radio fields. Mounting the 

antenna too close to the lighting system may also cause the radio noise 

emitted from the lighting system to interfere with the reception of the radio 

transmitter and reduce radio reception.

•  Do not attempt to wash any unsealed electrical device while it is connected to 

its power source.

During Installation and Service

•  DO NOT get metal shavings inside the product. Metal shavings in the product 

can cause the system to fail. If drilling must be done near the unit, place an 

ESD-approved cover over the unit. Inspect the unit after mounting to be sure 

there are no shavings present in or near the unit.

•  To avoid a battery explosion, always disconnect the negative battery cable first 

and reconnect it last. Avoid causing a spark when connecting near or to the 

battery. The gases produced by a battery can caused a battery explosion that 

could result in vehicle damage and serious injury.

•  DO NOT connect this system to the vehicle battery until ALL other electrical 

connections are made, mounting of all components is complete, and you have 

verified that no shorts exist. If the wiring is shorted to the vehicle body or frame, 

high current conductors can cause hazardous sparks, resulting in electrical fires 

or flying molten metal.

•  DO NOT install equipment or route wiring (or the plug in cord) in the 

deployment path of an airbag.

•  If a vehicle seat is temporarily removed, verify with the vehicle manufacturer if 

the seat needs to be recalibrated for proper airbag deployment.

•  Before mounting any components, check the manual to ensure that the 

component you are installing is suitable for use in that area of the vehicle. 

Many components are not suitable for use in the engine compartment or other 

extreme environmental exposure areas.

•  When drilling into a vehicle structure, ensure that both sides of the surface are 

clear of anything that could be damaged. Remove all burrs from drilled holes. 

To prevent electrical shorts, grommet all drilled holes through which wiring 

passes. Ensure that the mounting screws do not cause electrical or mechanical 

damage to the vehicle.

•  Refer to the manual packed with the lighting system for proper electrical 

connections, additional precautions, and information. 

Содержание Legend LGD





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды