Federal Signal Corporation Integrity Series Скачать руководство пользователя страница 41

Страница: 41 / 44

Maintaining and Servicing the Integrity

Installation, Maintenance, and Service Manual

Federal Signal

www.fedsig.com

Problem

Corrective Action

The light bar has a delayed response to

being shut off

• Ensure that the connections on the Serial Interface Module are kept

separate from strobe supplies.

• Check all the ground connections, especially on the Serial Interface

Module.

• Reset the controller (page 39).

A Flash Takedown/Alley light stays on

with ignition power applied

•  Ensure that there is no voltage on the corresponding control wire.
•  To see if the ROC board is bad, swap it with a similar board.
•  Swap the cables on the light bar controller outputs with a known

good output. If the problem moves to another halogen light, send

the light bar controller to Federal Signal for repair.

• Reset the controller (page 39).

Takedown/alley lights work, but Flash

Takedown/Alley lights do not work

• Ensure that 12 Vdc is applied to the takedown and alley (red/black)

control wire.

• Check the 12 Vdc power and negative ground connections to the

light bar to ensure there is enough current.

• Reset the controller (page 39).

Only one takedown light turns on

• Check the connections from the light bar controller to the ROC

boards and ensure they are in the proper locations.

• Reset the controller (page 39).

SignalMaster LEDs do not light

• Check the switch settings on the Serial Interface Module. Ensure

that they are set for the correct operation. See Table 5 on

page 15.

• Ensure that Switch 4 on SW-2 is in the correct position for the

selected operation on the Serial Interface Module and ignition power

was removed and reapplied.

• Check the connections at the SignalMaster controller. If the

controller is a model SS2000SM, ensure that the connector has

power and the ground is connected to pins 10 and 11 on the

SignalMaster plug.

• Reset the controller (page 39).

Содержание Integrity Series












































Результаты поиска

Содержание Integrity Series

Отзывы:

Похожие инструкции для Integrity Series

Бренды по названию

Популярные бренды

Federal Signal Corporation Integrity Series, Инструкция по установке, обслуживанию и ремонту

Результаты поиска

Содержание Integrity Series

Отзывы:

Похожие инструкции для Integrity Series

Бренды по названию

Популярные бренды