Federal Signal Corporation Integrity Series Скачать руководство пользователя страница 12

Страница: 12 / 44

Reprogramming the Light Bar

Integrity Light Bar

Federal Signal

www.fedsig.com

Reprogramming the Light Bar

HEAVY OBJECT: Use lifting aids and proper lifting techniques when removing or

replacing this product. Failure to heed this warning may cause personal injury.

Carefully unpack the light bar assembly and any other products included in the shipment.

Inspect them for damage that may have occurred during shipping. If a product has been

damaged, do not install or operate it. Immediately file a claim with the carrier describing

the damage.
Carefully check all envelopes, shipping labels, and tags before removing or destroying

them. If you are missing any parts, contact Customer Support at 1-800-264-3578, 7 am to

5 pm, Monday through Friday (CT).

Reprogramming the Light Bar

Although the Integrity light bar is configured and programmed at the factory, you may

want to change the default settings and flash patterns before installation. Before you

begin, decide if you want to change these default settings.

SignalMaster Operation: Internal (Factory Default) or External

• Internal operation uses the on-board SignalMaster controller in the light bar

to generate directional warning patterns. With Internal operation, an external

SignalMaster controller is not needed. A standard low current switch box can activate

the internal SignalMaster controller.

MODE 1, 2, 3, and INTERSECTION

• MODES 1 through 3 are most often selected by a progressive slide switch, which

enables the driver to turn on the light bar without looking down. You can select a

pattern for each mode from the light bar’s library of 26 patterns.

• The INTERSECTION flash pattern is typically a high activity pattern that attracts attention

to the vehicle as it approaches an intersection. You can select a pattern from the library

and choose one of three ways to turn on and off the pattern. The INTERSECTION flash

pattern overrides the three priority modes.

NOTE:

If the SignalMaster flash pattern is turned on, it overrides the current flash pattern.

FRONT and REAR lights: CUTOFF (default) or ENABLE

• Set these options after you change the default settings for MODE and INTERSECTION

flash patterns. CUTOFF turns OFF the front or rear LEDs when 12 Vdc is applied to the

FRONT or REAR light control wire. ENABLE turns ON the front or rear LEDs when 12

Vdc is applied.

Making the Electrical Connections for Reprogramming

To supply power to the light bar, use a fully-charged 12-volt automotive battery and follow

these steps:

Place the light bar on a sturdy, flat surface.

Plug the CAT5 communication cable (1) from the light bar into the Serial Interface

Module (J1). See Figure 1.

Содержание Integrity Series












































Результаты поиска

Содержание Integrity Series

Отзывы:

Похожие инструкции для Integrity Series

Бренды по названию

Популярные бренды

Federal Signal Corporation Integrity Series, Инструкция по установке, обслуживанию и ремонту

Результаты поиска

Содержание Integrity Series

Отзывы:

Похожие инструкции для Integrity Series

Бренды по названию

Популярные бренды