background image

Limited Warranty: 

This product’s limited warranty can be 

found at www.fedsig.com/SSG-Warranty.

SAFETY MESSAGES TO INSTALLERS AND USERS 

It is important to follow all instructions shipped with 

this product. This beacon is to be installed by a trained 

electrician who is thoroughly familiar with and will follow 

all applicable national and local codes in the country of 

use.

This beacon should be considered a part of the warning 

system and not the entire warning system.

The selection of the mounting location for the beacon, 

its controls, and the routing of the wiring are to be 

accomplished under the direction of the facilities engineer 

and the safety engineer. Listed below are some other 

important safety instructions and precautions you should 

follow:

• 

Read and understand all instructions before 

installing or operating this equipment.

• 

To avoid electrical shock hazards, do not connect 

wires when power is applied. Failure to observe this 

warning may lead to serious injury or death.

• 

Never alter the unit in any manner. Safety in 

hazardous locations may be endangered if additional 

openings or other alterations are made in units 

specifically designed for use in these locations.

• 

Do not connect this beacon to the system when 

power is on.

• 

After installation, ensure that all threaded joints are 

properly tightened.

• 

Keep the unit tightly closed when in operation.

• 

After installation, test the beacon system to ensure 

that it is operating properly.

• 

After testing is complete, provide a copy of this 

instruction sheet to all personnel.

• 

Brass inserts have the potential to store charge 

when they are not plugged. Consideration should be 

taken to prevent these from becoming a sparking 

hazard.

Model G-LED LED Beacon

For Use in Hazardous Locations

• 

The lens guard has the potential to store charge. 

Consideration should be taken to prevent this from 

becoming a sparking hazard.

• 

Establish a procedure to routinely check the beacon 

system for proper activation and operation.

• 

Maximum flash frequency is 90 FPM.

• 

This equipment is suitable for use in Class I, Division 

2, Groups A, B, C, D; Class II, Division 2, Groups F and 

G; Class III or non-hazardous locations only. 

• 

WARNING: EXPLOSION HAZARD — 

Do not 

disconnect the equipment unless power has been 

switched off unless the area is known to be non-

hazardous.

• 

WARNING: EXPLOSION HAZARD —

 Do not remove or 

replace the fuse when energized.

• 

The purchaser should make the manufacturer aware 

of any external effects or aggressive substances to 

which the equipment may be exposed.

Failure to follow all safety precautions and instructions 

may result in property damage, serious injury, or death to 

you or others.

With respect to the potential electrostatic charging hazard 

as mentioned in the certificate “Specific Conditions of 

Use,” under normal conditions of use, these devices 

are for fixed installations and not generally in contact 

with people. The risk of ignition is low. In addition, 

maintenance, cleaning, and extreme environmental 

factors (e.g., high velocity dust-laden atmospheres or 

high-pressure steam) should be taken into account by 

the end user using local Explosive Atmosphere (Ex) 

Electrical installation design, selection, inspection, and 

maintenance Codes and Standards. Cleaning of the 

devices should be done only with a damp cloth.

25500186 Rev B9 0523

Содержание G-LED Series











Отзывы: