manualshive.com logo in svg

FB Jets T33, Инструкция по сборке, Страница: 3 / 19

Поделиться
Скачать
FB Jets T33 Скачать руководство пользователя страница 3

 

 

FEI BAO/FB Jets Large T33 

Table of Contents 

DISCLAIMER........................................................................................................................................................ 2 

Introduction ....................................................................................................................................................... 4 

Adhesives ........................................................................................................................................................... 4 

Construction ....................................................................................................................................................... 5 

Preliminary steps ........................................................................................................................................... 5 

Step 1: Check Forward Fuselage .................................................................................................................... 6 

Step 2: Prepping the Fuel System .................................................................................................................. 6 

Step 3: Tank Installation ................................................................................................................................. 7 

Step 4: Nose gear ........................................................................................................................................... 7 

Step 5: Nose Doors ......................................................................................................................................... 8 

Step 6: Vertical Fin and Rudder ..................................................................................................................... 9 

Step 7: Horizontal Stabilizers ....................................................................................................................... 11 

Step 9: Speed Brake Setup ........................................................................................................................... 11 

Step 10: Engine and Pipe ............................................................................................................................. 11 

Step 12: Main Landing Gear and Doors ....................................................................................................... 12 

Step 13: Aileron and Flap Servos ................................................................................................................. 13 

Step 15: Cockpit ........................................................................................................................................... 15 

Step 16: Radio Programming ....................................................................................................................... 15 

Step 17: Weight and Balance ....................................................................................................................... 15 

Step 18: Test Flight ....................................................................................................................................... 15 

Equipment Installation Photos ..................................................................................................................... 16 

 

 

 

 

Содержание T33




















Отзывы:

Нет отзывов