FB Jets T33 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 19

FB Jets T33 Скачать руководство пользователя страница 16

FEI BAO/FB Jets Large T33

Equipment Installation Photos

•

Equipment, including fuelling tubes, switches, air fill, air gauges and remote ECU board were
all installed in on the component boards to have as much weight forward as possible. Also,
the  wiring  for  the  ECU  and  for  the  servos  was  run  down  opposite  sides  of  the  fuselage  to
avoid  interference.  The  receiver  was  mounted  on  the  front  component  board.  This  is  a
good  location  for  both  conventional  receivers  and  2.4  GHZ  units,  due  to  the  central
location,  high  mounting  point  and  absence  of  carbon  fibre  in  the  area.  If  you  are  using
multiple 2.4 receivers, this general location allows for additional units both fore and aft. The
positioning also allows for the shortest run of extension wires.

Parts List

•

Forward Fuselage and Component Boards

•

Aft Fuselage

•

Engine Hatch

•

Canopy

•

Horizontal Stabs, Elevators (2)

•

Vertical Fin, Rudder

•

Wings, Ailerons (2)

•

Main Landing Gear (2)

•

Nose Gear with Integrated Steering Bracket

•

Cockpit Tub, Rear Instrument Panel

•

Dual Wall Exhaust Pipe with Mounting Tabs

•

Upper and Lower Bypass

•

Linkage Assemblies (8)

•

Air Support Kit

•

Hardware Kit

«
...
14
15
16
17
18
...
»

Содержание T33




















Отзывы:

Нет отзывов