FAW Jiefang Automotive 485 Скачать руководство пользователя страница 50

Страница: 50 / 57

Trouble causes

Remedial methods

II. Abnormal engine-oil pressure

1. No or little pressure for engine-oil

(1) Engine-oil level too low; oil deteriorates or

is thinned.

(2) Oil pipe is broken; pipe joint not tight

enough causing oil leakage; engine-oil pressure

gauge is damaged.

(3) Engine-oil pump pressure-adjusting spring

is deformed or broken.

(4) Engine-oil pump has too much clearance.

(5) Engine-oil pump gasket is broken.

(6) fit clearance between bearings is too much.

(7) Oil-passage screw-plug is loosened and

leaks.

2. Engine-oil pressure too high

(1) Engine-oil pump's pressure-limiting valve

does work abnormally, oil-returning does not

go smoothly.

(2) Air temperature too low, engine-oil

viscosity too higher.

3. Rocker arm cannot be added engine-oil.

(1) Upper cylinder-head oil-passage and

oil-hole at support bottom of rocker arm shaft

are clogged.

(1) Add the oil; change the oil.

(2) Weld, tighten or replace it.

(3) Replace it.

(4) Return it to factory for repair; replace it.

(5) Replace it.

(6) Inspect, adjust or replace it.

(7) Inspect it; block it.

(1) Inspect and adjust it.

(2) Use engine-oil with brand specified;

decrease is possible after the engine is

warmed up.

(1) Clean and make it unclogged.

III. Smoke emitted in exhaust gas

1. Black smoke emitted in exhaust gas

(1) Oil injector is clogged with accumulated

soot, and needle valve is clogged.

(2) Load is too much.

(3) Fuel injecting is too late, and partial fuel is

burned during the course of exhaustion.

(4) Incorrect valve clearance; valve sealed

poorly.

(5) For each cylinder, fuel supply by

fuel-injection pump is not uniform and even.

(6) Intake pipe, air filter clogged, and air-intake

is not smooth.

2. White smoke emitted in exhaust gas

(1) Fuel-injecting pressure is too low;

atomization is poor; fuel dripping.

(1) Inspect, repair or replace it.

(2) Adjust the load to the range specified.

(3) Adjust the fuel-supply advance angle of

fuel-injection pump.

(4) Inspect the valve clearance and sealing

surface and spring force etc, and eliminate

the problems.

(5) Adjust fuel supply amount for each

cylinder.

(6) Dismantle and clean the filter.

(1) Inspect, adjust, repair or replace the fuel

nozzle couple.

Содержание 485


























































Результаты поиска

Содержание 485

Отзывы:

Похожие инструкции для 485

Бренды по названию

Популярные бренды

FAW Jiefang Automotive 485, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 485

Отзывы:

Похожие инструкции для 485

Бренды по названию

Популярные бренды