FAW Jiefang Automotive 485 Скачать руководство пользователя страница 4

Страница: 4 / 57

To Users

Dear Users :

When new diesel engines or engines just subjected to an overhaul (e.g., main parts such

as piston, crankshaft or connecting rod etc are replaced) are used on automobiles, the automobile

must not run at normal or heavy-load condition until it has run for a wear-in distance of 2000 km,

in which engine speed should be no more than 2200 r/min and power should be 70% of full-load.

This is very important to the reliability and after-overhaul service life of the engine. 4DW engines

will bring you more economic effectiveness if you timely maintain them as per this Manual.

Contact phone numbers of our Works are as follows:

Sales Company: 0510-85013436 (fax)

Main engine dept.: 0510-85014990-8362, 8363

Accessories dept.: 0510-85014990-8370, 85010814

Service dept.: 0510-85014990-8372, 8373

FAWDE 24h hotline: 0510-85017315

Production License No.: XK06-002-00014

FAW Jiefang Automotive Company, Ltd.

Wuxi Diesel Engine Works

August 2006

Содержание 485


























































Результаты поиска

Содержание 485

Отзывы:

Похожие инструкции для 485

Бренды по названию

Популярные бренды

FAW Jiefang Automotive 485, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 485

Отзывы:

Похожие инструкции для 485

Бренды по названию

Популярные бренды